Recent content by marcar1993

  1. marcar1993

    No headlights or tail lights

    There is no power at pin FZ, so I'll be rewiring it eventually. For now, I just took my wagon. Oh well, more work for winter.
  2. marcar1993

    No headlights or tail lights

    Per this thread, I need to check pin FZ on the c100 connector (firewall bulkhead) for power, it could be the fusible link on the starter. If it is, I'm running a PDC on the inner fender. That starter is near impossible to get to with the headers...
  3. marcar1993

    No headlights or tail lights

    I went to drive the car this morning, and I have no headlights or tail lights. Had them last week when I drove it. Turn signals and hazards work, brake lights work too. Pulled the switch and I am somewhat limited without a wiring diagram, but I have no power on the light switch side plug, and...
  4. marcar1993

    Can anyone take a pic of where this connects?

    Looking at this diagram I just need to ground the black wire from the c497 plug to do what the ecm is no longer doing then my factory harness will work. Does this sound correct?
  5. marcar1993

    Can anyone take a pic of where this connects?

    Ok so reading these posts jogged my memory. I tucked a bunch of wiring in the drivers fenderwell. I unrolled it all and there was my connector. Blower motor works on high now. (I did replace the relay too, fixed that issue too!) Tried hooking up the factory ac harness to the low pressure switch...
  6. marcar1993

    Can anyone take a pic of where this connects?

    I only have 3 pins, light green and black. Would the other side have been in the computer harness that comes through the passenger side firewall? I removed that (complete thankfully) a long time ago. I will look at the wiring coming up off the starter though, thank you. I may have it tucked out...
  7. marcar1993

    Can anyone take a pic of where this connects?

    I'm trying to make the high-speed blower work for the first time in 15 years of owning my car. I tracked it down to a lack of power in the red (always hot) wire on the high speed relay, which jumps power about 12" of wire away at this connector: Now I have temporarily run a constant power...
  8. marcar1993

    Msd box mounting

    The kick panel would be a great place if the box didn't have Rev limiter dials in it that need to be accessible. I want to keep it where I can just grab a small screwdriver and tune it without removing parts to get to it.
  9. marcar1993

    Msd box mounting

    I also want to keep my glove box, and I have a/c so ducts are staying! What is the mounting plate you're speaking of though? Do they sell them? I figure I could bend on up pretty easy if needed. My car is olds powered so flip flop the battery and charcoal canister for me, but I still have mine...
  10. marcar1993

    Msd box mounting

    Hey guys, long time no post. I'm looking to put in an msd 6al-2 and I'm having a tough time underhood finding a spot where it fits and is accessible for tuning the Rev limiters. Anyone have pics or suggestions? I'm just looking for what others have done. Might also put an underhood fuse box...
  11. marcar1993

    Mechanical or Hydraulic? (vote)

    Curious if you have pics of this and a better explaination? I have an lt1 t56 behind an olds with a wier conversion bell and been through a few junk mcleod slip on bearings, now I have a Tilton from modern drive line, and so far so good. I converted to a push style clutch in the tight lt1...
  12. marcar1993

    Air Conditioning System

    The short answer is no, that compressor is built with pag oil in it and to use pag oil. The system needs to be flushed, as it will have mineral oil in it, which is NOT COMPATIBLE with pag. Then refill with the proper amount of pag (whatever proper weight.) Typically when swapping from r12 to...
  13. marcar1993

    Axle swaps

    Idk what shipping would be like but I have a pair of stock 28 spline g body axles I'd let go of cheap. Let me know if you're interested.
  14. marcar1993

    Would Moog 5662s hurt 60ft times ?

    1.9 60' and low 12/high 11 et, you must be spinning or barely moving off the line then laying into it. My car had a bad bog and would still pull 1.8xx 60' falling on its face immediately after breaking the beams.
  15. marcar1993

    Driveshaft Loop Question

    My UMI one needed considerable modification in my car. There are no one size fits all in regards to these loops it seems.

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor