1980 Pontiac LeMans Station Wagon - G-T-faux (stuck with it, and can't shake it... like a bad case of herpes)

Status
Not open for further replies.

motorheadmike

Geezer
Nov 18, 2009
8,976
27,522
113
Saskatchewan, Truckistan
Trans is back in! Goodnight.
 
  • Like
Reactions: 6 users

motorheadmike

Geezer
Nov 18, 2009
8,976
27,522
113
Saskatchewan, Truckistan
So much electrical... argh! Note the washers under the trans mount - I started shimming the tail shaft to get the driveline angles in spec(ish).

20180520_220255.jpg
 
Last edited:
  • Like
Reactions: 4 users

motorheadmike

Geezer
Nov 18, 2009
8,976
27,522
113
Saskatchewan, Truckistan
Whataday!

Long story short the trans is looking like it needs a set of skyjackers to deal with the lift at the trans mount (so many shims) - but enough of that. Got the starter back on and tested (it cranks), the driveshaft loop in, driveshaft in, torque converter bolted down, reverse lights and NSS/shifter linkage working, trans cooler lines buttoned up, and I just finished segment swapping the tune for the 4L80E.

Still a ways to go - but progress is being made!
 
  • Like
Reactions: 3 users

Turbolq4

Royal Smart Person
Sep 25, 2017
1,732
4,207
113
Nampa Idaho
Whataday!

Long story short the trans is looking like it needs a set of skyjackers to deal with the lift at the trans mount (so many shims) - but enough of that. Got the starter back on and tested (it cranks), the driveshaft loop in, driveshaft in, torque converter bolted down, reverse lights and NSS/shifter linkage working, trans cooler lines buttoned up, and I just finished segment swapping the tune for the 4L80E.

Still a ways to go - but progress is being made!


Just out of curiosity, did you add the wiring for the input speed sensor? I didn't the first time around and that trans lasted quite a while like that. Not sure if that was a contributing factor in the transmissions demise or not. I added it this time. I don't have the nss hooked up at all.
 
  • Like
Reactions: 1 user

motorheadmike

Geezer
Nov 18, 2009
8,976
27,522
113
Saskatchewan, Truckistan
Just out of curiosity, did you add the wiring for the input speed sensor? I didn't the first time around and that trans lasted quite a while like that. Not sure if that was a contributing factor in the transmissions demise or not. I added it this time. I don't have the nss hooked up at all.

Yes I am running the front VSS input, I bought the Nelson harnesses (cheapest option I found). Pretty easy install.

I am using the factory NSS/column lock-out - adapting the mechanical linkage (for a second time) was quite the chore. The obvious alternative involved more wiring, micro switches, and some relays (ironcially the car has most of this pre-installed already). But, having things (ie. tail lights) working like factory is nice.
 

Turbolq4

Royal Smart Person
Sep 25, 2017
1,732
4,207
113
Nampa Idaho
Yes I am running the front VSS input, I bought the Nelson harnesses (cheapest option I found). Pretty easy install.

I am using the factory NSS/column lock-out - adapting the mechanical linkage (for a second time) was quite the chore. The obvious alternative involved more wiring, micro switches, and some relays (ironcially the car has most of this pre-installed already). But, having things (ie. tail lights) working like factory is nice.

My factory nss stuff and reverse lights are still functional on the column shifter. My harness has the 80e nss connectors but they aren't connected to anything.
 

motorheadmike

Geezer
Nov 18, 2009
8,976
27,522
113
Saskatchewan, Truckistan
My factory nss stuff and reverse lights are still functional on the column shifter. My harness has the 80e nss connectors but they aren't connected to anything.

Cool. I am running a floor shifter and long tubes which is a much more involved process to retain those components using the factory levers and brackets.
 
  • Agree
Reactions: 1 user

Northernregal

Sloppy McRodbender
Oct 24, 2017
3,359
12,826
113
Red Deer, Northern Montana territory
Cool. I am running a floor shifter and long tubes which is a much more involved process to retain those components using the factory levers and brackets.
Hope you post some pics of your solutions. I’m gonna be doing the same thing pretty quick.
 
  • Like
Reactions: 1 user

motorheadmike

Geezer
Nov 18, 2009
8,976
27,522
113
Saskatchewan, Truckistan
I think there are a few earlier on in this thread. But, I'll snap some more once I am back under the car again.
 
  • Like
Reactions: 1 user

motorheadmike

Geezer
Nov 18, 2009
8,976
27,522
113
Saskatchewan, Truckistan
Guess who decided to wake up?!

20180522_222840.jpg


20180522_222916.jpg


20180522_223054.jpg
 
  • Like
Reactions: 6 users
Status
Not open for further replies.

GBodyForum is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. Amazon, the Amazon logo, AmazonSupply, and the AmazonSupply logo are trademarks of Amazon.com, Inc. or its affiliates.

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor