Search results

  1. timo22

    Holley SBC Aluminum Intake

    As stated, a nice cleaned up intake. All threads are intact . For small block Chevy. 50.00 plus shipping. Thanks for looking. timo22
  2. timo22

    Fourdoor Rear Vent Window

    Well, I sold my Bonneville so I can’t use it. The unit is in great shape and is for the passenger rear door. I already had it boxed up for someone else that backed out. If necessary ,I can open it back up and take pics . 50.00 plus shipping Not sure if this will fit the other 4 door gbodys. timo22
  3. timo22

    GP Inner Fender Braces

    Well , starting to dig through my stuff and found these . A very nice set of braces for an 81 and up GP. Already refinished with clips and bolts for an easy 5 minute installation . 40.00 plus shipping Thanks for looking. timo22
  4. timo22

    SOLD GP. Bar

    Digging around my junk and found this . Nice solid bar cleaned up and ready to be refinished. 75.00 plus shipping. Thanks for looking. timo22
  5. timo22

    Anybody seen one of these?

    I’ve been looking for years and never could find one at the yards. But I just happened to check and found it on eBay. It will look nice on my Malibu dash timo22
  6. timo22

    Phoenix Members

    A long shot but an 83 Bonneville showed up at the Pull n Save Phoenix South. I need the front bumper cover. I love my Bonneville and have been letting my grandson use it a bit. Within 3 weeks , he hit a stop sign and messed up the bumper cover and moulding. Hopefully someone can help me out...
  7. timo22

    Rebuilt Carburetors

    Like a lot of guys here, I deleted the computer system on my Bonneville. I switched over the distributor but due to finances had to delay getting a non computer carb. Well after trying to get my best deal , I stumbled across National Carburetors in Florida. The guy even let me send a hot air...
  8. timo22

    Steering Column Question

    Over the years I have repaired some columns , mainly ignition locks and signal switches, but never really dug into one. Well, my brother has a couple 3rd Gen Camaros with loose tilt columns. After researching the topic and buying a pin puller, it turned out to go smoothly. Although it took me a...
  9. timo22

    Oil Sending Unit

    I have a question on my 82 Bonneville wiring. It had a 3.8 Buick V6 and I’m putting a SBC in it. I was able to get a gauge pack for it to convert it from the dummy lights. The oil pressure sending unit is a one wire switch which is right for an 83 Bonnevile with a 305. (305 was not available in...
  10. timo22

    Blazer Brakes on 14x6

    I’m getting closer to figuring out my brakes on my Bonneville. I’ve already done the backs with new cylinders, shoes and hardware. The fronts will need calipers, hoses and pads. But I do have a complete Blazer set that I got a year ago. It had new rotors, bearings, caliper and pads so I took the...
  11. timo22

    Oil Pressure Sending Unit

    I am in the process of swapping a Chevrolet 305 in my Bonneville. I want to switch the idiot lights to factory gauges. I was lucky enough to find a working gauge set out of a GP at the junkyard. I looked up the sending units on Rock Auto and the temp unit is 5 or 6 dollars. Now when I look up...
  12. timo22

    Ground Strap 82 Bonneville

    Well I pulled the V6 (3.8) and th350 out of the Bonneville last weekend. Everything went well except I missed a heavy ground strap and pulled the end off it. It was on the driver side lower transmission bolt and goes between the frame and the body. I've never run across a heavy(battery size)...
  13. timo22

    Got Another One

    Well, I needed another GBody like I need another hole in my head. I have 65 Malibu SS, my 81 Malibu , the 82 Bonny, a 76 CJ5, a 41 Willys and my daily 15 Camry. But I just couldn't pass on this 84 El Camino . It's an original owner with 74xxx miles on it. Very solid with a little rust on the...
  14. timo22

    Putting a face on a Name

    I have worked at a lumber yard for over 35 years . I have done a lot of buying and selling over the years mostly on the phone. It has always amazed me how we have preconceived ideas of how someone looks based on their name,voice,personality, and location. To this day, I have never even been...
  15. timo22

    Any Northwest Washington State Members?

    My best buddy found a 75 Trans Am 4 spd car at Pacific Classics. It' s identical to the one he had in high school. I was hoping someone up there was close or new about these guys..timo22
  16. timo22

    Bonneville Headliner

    Just curious about removing my headliner in the Bonny for a recover. It honestly looks like it is too big to get it outside the car. I had no problem with my tudor . But that's because the door opening is wider. I guess if I take out the front seat , it will slide out? I haven't measured it out...
  17. timo22

    A++ Buckeye79

    Just want to put this out there for everybody. I bought a GP dash bezel off of Steve . He communicated quickly and sent me pictures. His description of the part was honest and accurate. We agreed on a fair price and he shipped in a timely fashion. My biggest concern was that the bezel arrive...
  18. timo22

    Cutlass in Calgary

    A Cutlass just showed up at the Picknpull in Calgary .(Barlow Trail) Its an 80 and says W30 on the fender. Looks like someone needs to check it out..I saw it on Row52..timo22
  19. timo22

    Regal on Row 52

    A nice looking Regal came in the Calgary Picknpull on March 3rd. Don't know if any members are close but it looks like it's in good shape with a nice hood. timo22
  20. timo22

    A++ Poncho64

    Just want to let everybody know that poncho64 is a great person to deal with. Parts were delivered quickly and parts were as described. I wouldn't hesitate to purchase from him again...timo22

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor