Search results

It doesn't look too bad, however I'm not familiar with the way elkys are put together. seems like the damage was contained just to the lower section. How does the door jamb look? any signs of cracked paint ?

I've toyed with the idea of LED tails in the cutty. haven't found a good layout for them being they are tall and skinny and not like the buick. making the boards and stuff for the taillights isnt hard, just mounting them in the lens and potting them well to prevent corrosion and shorts. Throw...

I figured it out, nothing looked lined up until i started tightening stuff down. Turns out the picture i have originally posed was the correct orientation of the spacer and the bracket.

hey guys, in the middle of replacing my water pump i didnt take note of the way the a.i.r pump bracket attaches with the a/c pump. I have the front bracket in front of the ac pump bracket. on the back side i have the spacer as seen in the picture followed by the air pump bracket. however i...

http://www.justclippsauto.com/ found all the clips for my landu top and my lower chrome moldings. ken and arlene are great people to do business with.

crapsman stuff has gone down hill in the last decade or two. I just got a good deal on a jack, creeper, jack stand combo. Wouldn't you know it the jack was unable to maintain pressure and slowly drop the car back onto the floor. Here is the best part, I got it replaced, but the manager of...

Thanks Anubis , its been a little while since i've been on the forum, hopefully with the weather warming up and getting things situated, i hope to get this part of the project going again.

I remember growing up these cars were everywhere, then when i started to look for one as my first car back in 99 / 2000 they started thinning out. As others have said the Northeast weather / road salt turned most of them into rust then add the cash for clunkers and now im lucky to see one...

the PTFE you are talking about will hold up well under the chemical environment they are subjected to, in addition the heat cycling shouldn't bother it too much. I use PTFE sheets in my environmental chambers at my job. They last no problem at 170C = 338F

I found my 8.5 ( 3.73 open rear) locally here in NJ a few years back, Came from an 84 H/O IIRC that was t- boned and the Kid bought it thinking it was repairable. He did not know what he had being he cut the shifter cable for the lightning rods. I got my rear end with the e brake cables and...

Welcome ! Hope to see you around next season at the local car shows! Typically i Stick around the Freehold / Howell area

the Idea I have is to use one or two sensors up on the radiator like most typical stock setups I've seen are. the additional sensor would be on the engine, to monitor the temperature on the block side. my idea behind this is to keep the temperature as stable as possible and using the additional...

The relay control is a good basic way to start out, and yes amperage of the fans has to be considered to a point. You guys gave me a great idea for a programmable fan control project, really simple to do with the arduino micro-controller development kit i have. A high/low fan speed can be...

check out http://www.justclippsauto.com/ ken and his wife are great people to deal and helped me find my lower chrome molding clips for my cutlass and the landu top clips i dont know if they remember me, but tell them dave with the 86 cutlass from NJ said hello!

yah i not sure if that's the same brochure I have, but the two pages you posted look similar except i think mine illustrated the dark blue dash with the rallye pac cluster and different wheel. I haven't dug it outt of my book shelf but i do recall they have a check list grid with the possible...

This was my Dad's old wagon when I was a kid

I believe that was the brochure for the 1986, being that's the year cutlass I have. Like i said i don't know if it was possible to have a factory or-dealership installed option on the H/O's.

not sure about the H/O specifically. However I did find out from the brochures I have that you could have had a landu top on a legit 442. As 88hurstolds mentioned could have been a dealership only instillation instead of factory

welcome! lots of guys on this forum are really knowledgeable and with more aftermarket performance parts from vendors that visit this site you should find all the help you need!. BTW what area of jersey?

thought the older reverse lights had a red reflector in them for the 83-84 's the ones you guys posted look like my original 86's with and without the stripe