Just purchased the Viper 5706v remote start/security. My MC is stilled carb’d; I hope the upgrade to the EFI in the future but for now will install the security side of the kit only. I was sold on the 1 mile transmitter range and ability to add their GPS service with this unit.
I currently have Autopage XT-59 with basic hook-up: park lights flash, keyless entry, door pin trigger, shock sensor trigger. MC is originally equipped with power locks and stock solenoid system still functions. I did disconnect the alarms door lock wires a while back as I had the driver side actuator go bad and forced to open manually.
I’m hoping to disconnect the Autopage and connect Viper wires for a plug and play swap but I have some doubts/questions given Viper wiring may be different. Car is in the shop right now but I recall seeing one (or two) relays under the dash within Autopage harness. I will double check what’s there once I get the car back.
Below is a picture of the inbox Quick Reference Guide along with wires I think are required or I’m uncertain of.
6 Pin:
Required to connect: #1, 2, 3, 5 and…?!
#6 – Is this a remote start function, only? If not, what is it for? If required, where to connect?
3 Pin:
Required to connect: #1 and 3
#1, 3 - According to this guy’s video
, his keyless system didn’t require an additional relay. However according to monte7carlo9 (“wiring alarm” thread), relays are required. Thoughts? If relays required, I have several sources on how to add so I’m good here.
10 Pin:
Required to connect: #7 only…?
#7 – Is this the alarms starter-kill function in case someone breaks in and attempts to turn on while siren is blazing? If so, cut my purple starter wire and feed in/out of this? If it is starter kill, this function should still work even if all other wires on this harness are not hooked up, right?
24 Pin:
Required to connect: #4, 9, 18 and...
#21 – Is this a remote start function only? If not, what for?
#4 – I heard triggering the dome light when arming/disarming requires a relay. If so, I delay installing for the moment.
#9 – Is this a stand-alone sensor? Or does this only work when the remote start is functional? I would like this function.
#18 – If monte7carlo9 is correct and door lock is a positive pulse, I match 18(+) vs 15(-) to the door pin?
Did I exclude a required connection for basic security function? Or include an unnecessary connection? Thanks in advance for any feedback!
I currently have Autopage XT-59 with basic hook-up: park lights flash, keyless entry, door pin trigger, shock sensor trigger. MC is originally equipped with power locks and stock solenoid system still functions. I did disconnect the alarms door lock wires a while back as I had the driver side actuator go bad and forced to open manually.
I’m hoping to disconnect the Autopage and connect Viper wires for a plug and play swap but I have some doubts/questions given Viper wiring may be different. Car is in the shop right now but I recall seeing one (or two) relays under the dash within Autopage harness. I will double check what’s there once I get the car back.
Below is a picture of the inbox Quick Reference Guide along with wires I think are required or I’m uncertain of.
6 Pin:
Required to connect: #1, 2, 3, 5 and…?!
#6 – Is this a remote start function, only? If not, what is it for? If required, where to connect?
3 Pin:
Required to connect: #1 and 3
#1, 3 - According to this guy’s video
10 Pin:
Required to connect: #7 only…?
#7 – Is this the alarms starter-kill function in case someone breaks in and attempts to turn on while siren is blazing? If so, cut my purple starter wire and feed in/out of this? If it is starter kill, this function should still work even if all other wires on this harness are not hooked up, right?
24 Pin:
Required to connect: #4, 9, 18 and...
#21 – Is this a remote start function only? If not, what for?
#4 – I heard triggering the dome light when arming/disarming requires a relay. If so, I delay installing for the moment.
#9 – Is this a stand-alone sensor? Or does this only work when the remote start is functional? I would like this function.
#18 – If monte7carlo9 is correct and door lock is a positive pulse, I match 18(+) vs 15(-) to the door pin?
Did I exclude a required connection for basic security function? Or include an unnecessary connection? Thanks in advance for any feedback!
Attachments
Last edited: