Kore3 C5 Front and Rear question

Status
Not open for further replies.

CDUNIGAN1981

Master Mechanic
Mar 15, 2015
307
347
63
Im here for the installation pictures

I'll post when I get there. Reaching out to SSM tomorrow to finalize front suspension. Afterwards, I'm making decisions about kore3 kits. Not sure how I feel about no parking brake in rear. Get the feeling 355mm up front might be too much for my 18"s as I've read certain American Racing wheels have issues even in 18", needless to say, I'm measuring.

With that, if I'm all eyes myself.
20200505_210625.jpg
20200505_210636.jpg
 

carnutjw

G-Body Guru
Sep 17, 2017
623
1,466
93
http://www.kore3.com/tech.php#fitment_templates. Scroll down to templates. You might have to scale your printout to make it right, there's a ruler on the side. Transfer to cardstock/poster board and check fit on the inside of your wheel. Also, if you order from them you get a pdf with multiple pages of instructions and 3D illustrations, very easy to understand and install.
 
  • Informative
Reactions: 1 user

CDUNIGAN1981

Master Mechanic
Mar 15, 2015
307
347
63
http://www.kore3.com/tech.php#fitment_templates. Scroll down to templates. You might have to scale your printout to make it right, there's a ruler on the side. Transfer to cardstock/poster board and check fit on the inside of your wheel. Also, if you order from them you get a pdf with multiple pages of instructions and 3D illustrations, very easy to understand and install.

I did see this but didn't immediately understand how to use it until just now. When I read 'wheel hub ' I just assumed I needed my hubs installed on my spindles first so I walked away from it after about 3 seconds of reading.

First time caller...yikes

Thanks for pointing this out. It will allow me to order it sooner.
 
  • Like
Reactions: 1 user

CDUNIGAN1981

Master Mechanic
Mar 15, 2015
307
347
63
I emailed kore3 for an opinion.
With that, does this look right?

I mean at the risk of affirming my ignorance.
Did I do this right?
Is 3/8" okay?

Corey
 

Attachments

  • 20200509_063255.jpg
    20200509_063255.jpg
    1.4 MB · Views: 182
  • 20200509_063457.jpg
    20200509_063457.jpg
    1.5 MB · Views: 188
  • 20200509_063515.jpg
    20200509_063515.jpg
    1.2 MB · Views: 190
  • 20200509_063529.jpg
    20200509_063529.jpg
    1.1 MB · Views: 240
  • 20200509_063534.jpg
    20200509_063534.jpg
    1.1 MB · Views: 179

Dayzedandkonfuzed

G-Body Guru
Feb 9, 2010
971
1,268
93
Anglemont, BC
I mean at the risk of affirming my ignorance.
Did I do this right?
Is 3/8" okay?

Corey


Oh yea bud. I dont think I even have 1/4" on my front setup, almost had to grind the fins down.

 
  • Like
Reactions: 1 user

CDUNIGAN1981

Master Mechanic
Mar 15, 2015
307
347
63
Oh yea bud. I dont think I even have 1/4" on my front setup, almost had to grind the fins down.


What size wheel were you working with?
 

CDUNIGAN1981

Master Mechanic
Mar 15, 2015
307
347
63
http://www.kore3.com/tech.php#fitment_templates. Scroll down to templates. You might have to scale your printout to make it right, there's a ruler on the side. Transfer to cardstock/poster board and check fit on the inside of your wheel. Also, if you order from them you get a pdf with multiple pages of instructions and 3D illustrations, very easy to understand and install.

Super helpful pointing this out my guy!
 
Status
Not open for further replies.

GBodyForum is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. Amazon, the Amazon logo, AmazonSupply, and the AmazonSupply logo are trademarks of Amazon.com, Inc. or its affiliates.

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor