What did you do to your non-G body project today? [2020]

Status
Not open for further replies.

ssn696

Living in the Past
Supporting Member
Jul 19, 2009
5,546
6,671
113
Permanent Temporary
If you were any kind of real father she'd be holding an incandescent drop light while crying and ducking empty WD40 cans.

Nope. New world. Demonstrating your trust in her by putting your hands in the machinery while she listens for the command to ‘start’.
 
  • Haha
Reactions: 3 users

Cauterize

Floater of Valves
Supporting Member
Feb 9, 2019
509
1,528
93
Deathbridge
Finally got the fork I ordered 3.5 months ago. Massive upgrade over the stock. Between the new wheelset and fork its like I have a whole new bike.
 

Attachments

  • 20201002_162530.jpg
    20201002_162530.jpg
    2.7 MB · Views: 97
  • Like
Reactions: 2 users

Gig

Apprentice
Feb 5, 2020
52
52
18
San Antonio
Putting in my trans in my camino
 

Attachments

  • EF0EAD57-C8A2-4CF2-8A5A-529A4B31E4ED.jpeg
    EF0EAD57-C8A2-4CF2-8A5A-529A4B31E4ED.jpeg
    3.1 MB · Views: 112
  • Wow
Reactions: 1 users

Gig

Apprentice
Feb 5, 2020
52
52
18
San Antonio
Putting in the trans in my 85 Camino
 

Attachments

  • 7CB8E2EF-9986-4933-BDCC-AFD34CB0BBBC.jpeg
    7CB8E2EF-9986-4933-BDCC-AFD34CB0BBBC.jpeg
    3.1 MB · Views: 288
  • Wow
Reactions: 1 users

Wageslave

Royal Smart Person
Jan 25, 2017
1,750
3,341
113
Making my Grand Cherokee a little less rusty.
IMG_20201006_232555.jpg


IMG_20201006_232528.jpg



I only have the top side welded in so far but 6 feet of weld bead, 2 inches at a time is a little time consuming. I figure each side is going to take about 14 feet of bead, or so. I have a feeling that I will find the end of my argon tank before this project is over.
 
  • Like
Reactions: 5 users

81cutlass

Comic Book Super Hero
Feb 16, 2009
4,649
13,565
113
Western MN
Going to look at this Poor-maro today because 6.0 winter beater for cheap

poor financial decisions.....

1602080040926.png
 
  • Like
  • Haha
  • Friendly
Reactions: 5 users

81cutlass

Comic Book Super Hero
Feb 16, 2009
4,649
13,565
113
Western MN
The Caprice was a Crap-piece

$8500 in decent shape is about average for LS Cappy PPV's and this one was only $4000 with 110K miles, but this one was not worth putting back on the road at least for me. If I knew VE commodore chassis cars it would be an easy buy, or if I parted them out and wanted a L77/6l80e combo for a restomod, but this needed too much work to put back on the road. Heck, even if this was just a wiring issue and a clean the interior project I might bite.

Trunk lid was dented, rear bumper was dented and scuffed, front bumper was off, passenger front door dented, passenger front fender dented, interior needed a good cleaning, tires were shot. It needs $3000 of wheels, tires and body panel replacement plus chasing down the no start.

Wiring was questionably spliced when the PD decommissioned it. The owner bought it at auction 'running and driving' only to find out it was mis-represented and it had no-start written on the window. Owner and mechanic buddy were fiddling with it and realized they were in over their heads. I brought my Laptop and HPtuners to plug in and at least see if the ECM had power (it didn't) and they oogled over my fancy scanner.

No power to the front fuse block, wires twist tied to the BCM, dozens of relays, modules and fuses in the trunk.

Nope, she's an engine donor. I can deal with just body work, I can deal with just a no start, or I can deal with a car that needs cleanup work and general 'tuneup' stuff, but I'm not dealing with all 3.

1602101540786.png

1602101932061.png
 
  • Wow
  • Haha
Reactions: 6 users

Northernregal

Sloppy McRodbender
Oct 24, 2017
3,359
12,828
113
Red Deer, Northern Montana territory
The Caprice was a Crap-piece

$8500 in decent shape is about average for LS Cappy PPV's and this one was only $4000 with 110K miles, but this one was not worth putting back on the road at least for me. If I knew VE commodore chassis cars it would be an easy buy, or if I parted them out and wanted a L77/6l80e combo for a restomod, but this needed too much work to put back on the road. Heck, even if this was just a wiring issue and a clean the interior project I might bite.

Trunk lid was dented, rear bumper was dented and scuffed, front bumper was off, passenger front door dented, passenger front fender dented, interior needed a good cleaning, tires were shot. It needs $3000 of wheels, tires and body panel replacement plus chasing down the no start.

Wiring was questionably spliced when the PD decommissioned it. The owner bought it at auction 'running and driving' only to find out it was mis-represented and it had no-start written on the window. Owner and mechanic buddy were fiddling with it and realized they were in over their heads. I brought my Laptop and HPtuners to plug in and at least see if the ECM had power (it didn't) and they oogled over my fancy scanner.

No power to the front fuse block, wires twist tied to the BCM, dozens of relays, modules and fuses in the trunk.

Nope, she's an engine donor. I can deal with just body work, I can deal with just a no start, or I can deal with a car that needs cleanup work and general 'tuneup' stuff, but I'm not dealing with all 3.

View attachment 158953
View attachment 158954
That could have been so cool.... 🙁
 
  • Agree
  • Like
Reactions: 2 users

81cutlass

Comic Book Super Hero
Feb 16, 2009
4,649
13,565
113
Western MN
That could have been so cool.... 🙁

Ditto. 380hp winter beater would be real fun, and I have some money burning a hole in my pocket from the wagon sale, but this isn't the place that money should go.
 
  • Like
Reactions: 4 users
Status
Not open for further replies.

GBodyForum is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. Amazon, the Amazon logo, AmazonSupply, and the AmazonSupply logo are trademarks of Amazon.com, Inc. or its affiliates.

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor