Recent content by RegMan79

  1. RegMan79

    Issues after swap. Intake/carb

    On the front and back walls and around the water jackets/exhaust. I'm asking specifically about the front and back wall
  2. RegMan79

    Issues after swap. Intake/carb

    So it ended up being a vacuum leak at the intake. I took it all apart and re did it today. I'm just waiting for the gasket maker to dry until tomorrow. Question, would turning the engine over by hand cause the gasket maker (on the front and back) to get sucked in or pushed out? The gasket maker...
  3. RegMan79

    Issues after swap. Intake/carb

    Summit was cool. They sent me a new intake gasket just in case I did give my self an intake vacuum leak. This was my first swap so I may have knocked rtv off the front/back walls when adjusting it. My uncle had given me this car about 6 months ago. He's had it for 10 plus years and thought it...
  4. RegMan79

    Issues after swap. Intake/carb

    Hello everyone. So I swapped my intake and carb last week (first time). I finally got it running, but not well. It's hard to keep running and it back fires at half throttle also I'm seeing some smoke out the valve covers. It ran good before the swap and only smoked for a second on start ups...
  5. RegMan79

    79 Monte hesitation/bogging

    Thanks guys I'll try and get ahold of him. The fuel tank is still the original one. I was saying maybe something got sucked up from the tank when I ran it out of gas. The fuel pump was replaced when the carb was rebuilt.
  6. RegMan79

    79 Monte hesitation/bogging

    Do you think it sounds like I didn't put something back together right?
  7. RegMan79

    79 Monte hesitation/bogging

    Hello again guys. I have the 267 engine with the dual jet 210 carb. Been running good until recently. I've had this car for about 5 months now, uncle have it to me. Anyway, I'm experiencing a slight hesitation or bogging down like running out of gas under light acceleration. If you smash on...
  8. RegMan79

    Dual jet 210 carburetor spring location

    I took my carb off to clean the intake and carburetor. This little spring popped out from somewhere not sure where it goes. 79 Monte 267 engine Dualjet 210 carb. The model number is in the picture
  9. RegMan79

    First G Body - Clean 78 MC

    Welcome to the forum man! I have a 79 MC, they're great!
  10. RegMan79

    79 Monte computer??

    Sweet I was worried. This makes me feel better
  11. RegMan79

    79 Monte computer??

    Does the 79 Monte have a computer? I've heard yes and no. I'm putting an edelbrock performer manifold on soon. Wondering if removing the EGR or other emissions components will cause performance issues. Heard the computer controls carb and dizzy.
  12. RegMan79

    Torsen 28 spline posi upgrade

    I must have just seen the same chip twice because I'm not seeing another one. Just the 1
  13. RegMan79

    Torsen 28 spline posi upgrade

    Yeah I'm pretty sure there was a second one I'll have to look at it again when I'm home. I'll take a picture and Post. Yeah I understand just the ring and pinion possibly
  14. RegMan79

    Torsen 28 spline posi upgrade

    Yeah there is 2 from what I seen. I think it's a 98 instead of an 01. Other what? Pics?
  15. RegMan79

    Torsen 28 spline posi upgrade

    Here it is. Let me know what you guys think. I think every thing is here. There's a chip or 2 on the pinion head.
See more

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor

Top Bottom