Search results
-
What are you guys doing for fuel systems on your efi LS conversions?
This is true. Mine has been really good to me. It was a Wix, I had ran it with a walbro 255. Mine ran a little high at 63 ish psi. That said I lot of people I know have had issues with newer ones, even Wix branded. Not sure if someone posted it since I have read the whole thread. Holley have...- DSPbuilt
- Post #10
- Forum: G-Body LS Swap
-
What did you do to your G-Body today 2024
Short Strand Bondo fiber. On the parts I did a year ago it’s held on well. My only issue and it could be the Florida humidity, is the the working time is short and it stays gummy for a long time. I put it on yesterday around 1-2pm and it’s still gummy this morning.- DSPbuilt
- Post #179
- Forum: General Discussion
-
What did you do to your G-Body today 2024
Barfed all over the dash..- DSPbuilt
- Post #174
- Forum: General Discussion
-
-
What did you buy for your G-body today? [2024]
Finally bit the bullet and ordered a CPP rear sway bar. After talking to 64nailhead and 81cutlass it seems like a decent choice for the money. Also picked up another set of draglites I was finally able to find a decent used set with the right backspace. Also ordered new 5/8 studs. Some of mine...- DSPbuilt
- Post #95
- Forum: General Discussion
-
What did you buy for your G-body today? [2024]
Couple weeks ago I found a killer deal in Market Place for 3 Draglites. Two rear 15x10 and one front(which I can’t use because of the brembos). He was not sure of the backspace but $150 I could not pass up the deal. Worst case I’ll polish them and resell for nice profit. They seem to be about...- DSPbuilt
- Post #82
- Forum: General Discussion
-
-
-
-
Steering box.
it even already has another fitting location on the bottom… https://www.jegs.com/i/JEGS/555/60731/10002/-1?gad_source=1&gclid=EAIaIQobChMIifzSsuffhQMVv6NaBR2CRQByEAQYAyABEgIk9fD_BwE- DSPbuilt
- Post #7
- Forum: Frame / Chassis / Suspension / Steering
-
Steering box.
They make aluminum reservoirs for those. Might be a better option. You can essentially put the return anywhere you need.- DSPbuilt
- Post #3
- Forum: Frame / Chassis / Suspension / Steering
-
-
Frame notch and back spacing
Sounds about right. My current setup is 18x10.5 with a 295/45 with 5.37in bs 5.5 seems to be the mark for 15x10 275/60- DSPbuilt
- Post #11
- Forum: Wheels / Tires / Brakes
-
What did you buy for your G-body today? [2024]
Ever since I got the 8.8 I had some internal struggles with how I wanted to finish it out. The rear had your typical inboard drag style coil over mounts and backyard special LCA mounts. The coil over mounts would not work for me because the exhaust. I have the Hooker Black Heart 3” kit. I have...- DSPbuilt
- Post #65
- Forum: General Discussion
-
-
-
Frame notch and back spacing
Just did my notch. From what I have seen just about everyone runs 5.5in bs. 5.25 should assuming you went to about the seam.- DSPbuilt
- Post #2
- Forum: Wheels / Tires / Brakes
-
CUTLASS Close Call - AN fitting failed
I avoid the ones with the plastic clips at all cost. These are the ones you want to go with. plenty have ran pretty high HP builds with this style. https://www.russellperformance.com/6an-male-x-1-4-sae-quick-disconnect-female-threaded-cap-fitting-black-finish-641303.html- DSPbuilt
- Post #12
- Forum: Fuel / Air / Boost / Emissions
-
Rear sway bar with tubular arms
The easiest option is something of this nature. On mine I'm going the ARB route. You can also do the Blazer rear bar which some here have done. I picked one up but the arms are in the way of my exhaust...- DSPbuilt
- Post #3
- Forum: Frame / Chassis / Suspension / Steering
-
-
On the Cheap chasing an 8.50
Nice! Did you weigh the two tubes to compare? I’ve seen plenty of people do that but usually put one tube back in.- DSPbuilt
- Post #817
- Forum: G-Body Racing
-
What Did You Do To Your G-Body Today? [2023]
Working on getting this unit and myself dialed in. I do think the pedal they supplied is bad. When I tried to practice on aluminum it seems to be erratic, kinda starts then stops. It was sort of doing the same with in DC on the steel. I switched over to the torch button and it seems to be...- DSPbuilt
- Post #1,314
- Forum: General Discussion
-
What Did You Do To Your G-Body Today? [2023]
as usual I disappear for a little then I get finally get a few things done. 🤣 I recently picked a tig welder. So I’ve mostly been practicing on that. Also picked up some used Nitto drag radials to test fit… Well they didn’t fit.. 295/45/18 So I made the logical choice and cut the frame. It was...- DSPbuilt
- Post #1,311
- Forum: General Discussion
-
-
What did you buy for your G-body today? [2024]
That was also my understanding. What I have also seen is some order the 6550 but get a standard ratio.- DSPbuilt
- Post #5
- Forum: General Discussion
-
Delco 1.5 CD Player... better than the tape decks power wise?
These are pricey but real nice. https://www.retromanufacturing.com/collections/1-5-din-radios/products/retrosound-newport-1-5-din-radio?variant=42656868761756- DSPbuilt
- Post #3
- Forum: Electrical / Ignition / Starting
