Search results
-
What did you do to your non g-body project today [2025 edition]
Yer Granpa had a v-twin.......- WanaBa442
- Post #169
- Forum: Non-G Projects
-
install posi
Used to be common to use in Jeep Cj's, Scouts, and possibly some early Scouts. Made them for Jeep Dana 25,27,30 front axles, 44 rears. Some Chrysler rear and older GM's. Be interesting to see what reply you get from the seller....- WanaBa442
- Post #28
- Forum: Transmission / Rear End / Driveline
-
Funny Car Related meme's
- WanaBa442
- Post #6,513
- Forum: Photos, Videos, etc.
-
-
Odometer reading question
Does the 5th digit ( white one) read tenths or only changes for every mile?- WanaBa442
- Post #3
- Forum: General Discussion
-
HELP GM AFM delete?
Anyone using an AFM delete device on a 5.3 Silverado? Picking up a new to me 2013 Silverado LT with 55k original miles to replace my clapped out Tundra. Don't need a " tune" capable unit as it's going to be my DD, maybe haul my camper a few times a year. Favorites, real world experiences? Tks. -
best gear ratio
Carrier break is at 3.08. That and numerically lower are series II 3.23 and up are series 3. If you're going that route I'd stay away from an offshore "posi" for less than $200. Find a Camaro rear with a Torsen unit and gears and bolt it in. Axle spline count is different than your stock 26...- WanaBa442
- Post #21
- Forum: Transmission / Rear End / Driveline
-
-
What did you do to your G-Body today 2024
As my neighbor, the 90 year old farmer used to say " She come from together"......- WanaBa442
- Post #671
- Forum: General Discussion
-
oil pressure sensor (new parts)
The a NOS one on another forum for $399.00 if you're so inclined...........😱- WanaBa442
- Post #9
- Forum: Chevrolet Monte Carlo / Monte Carlo SS / Malibu
-
-
-
Sbc 350 harmonic balancer
If you're just replacing the seal, why do you not want to reuse the balancer that is on there now? Barring a groove worn in it, it should work fine and seal up on the new seal, no? At least you know it'll fit without spending money for no reason.....- WanaBa442
- Post #8
- Forum: Engine / Swaps / Driveability
-
The Spotted Thread
- WanaBa442
- Post #2,462
- Forum: General Discussion
-
Happy 4th of July!!!!
Went to the local parade, an hour long with every local VFD in line. Tractors, classic cars, some very well done floats. Highlight for me was the VT Air Guard flyover with a pair of F-35's at low altitude. First pass woke everyone up, looped around for a second one with the candles lit..... 🇺🇲- WanaBa442
- Post #10
- Forum: General Discussion
-
-
Making a High Horse Power 307
I remember when you read a book by Doug Roe, David Vizard, or a Peterson Publishing rag and hung out with gear heads and got the same answers ...... What's old is new again🤔- WanaBa442
- Post #3
- Forum: General Discussion
-
Funny Car Related meme's
- WanaBa442
- Post #6,223
- Forum: Photos, Videos, etc.
-
CadiRat adventures
Duuuude.... That thing is mint..... Throw a few rust blisters on there and you'd have mint chocolate chip🤔 I'd wheel it👍- WanaBa442
- Post #10
- Forum: Non-G Projects
-
-
Firewall Wire
Looks like the tach signal wire?- WanaBa442
- Post #2
- Forum: Electrical / Ignition / Starting
-
The cost-benefit to owning cars??
- WanaBa442
- Post #25
- Forum: General Discussion
-
What did you do to your G-Body today 2024
Pulled it out of storage this morning. Fired right up, ran like an old Olds always does. TH 200 lost some life blood over the winter, time to freshen up a TH350 I've got waiting in the wings.- WanaBa442
- Post #68
- Forum: General Discussion
-
-
Driveshaft lengthening sanity check
Didn't see it mentioned but if you're staying with stock suspension and rear axle I'd source a shaft from one of the million or so G bodies that came with the TH200 and 7.5 rear Bolts right in.- WanaBa442
- Post #3
- Forum: Transmission / Rear End / Driveline
-
Funny Car Related meme's
This one's for CK80. Hope you're doing well- WanaBa442
- Post #6,135
- Forum: Photos, Videos, etc.
