Search results

It is leaking quite from the seal and there definitely slop at the far end of the driveshaft. it does make sounds, kinda like how an old car sounds like, but its not very loud and you can only hear it when letting of the throttle, not when accelerating.

Yeah thats what i figured. but as a temporary fix while i'm looking for a replacement, does anyone have experience with tightening it up, im thinking about how long (miles) and how safe. thanks for the input

I have a 1980 malibu with a 350 transmission and open diff rear end. My car makes loud clicking noises when i change from park to reverse/drive or reverse to drive etc. also makes click when i accelerate hard. there is about 3-4mm of up and down slack where the driveshaft meets the...

Whenever i start up my Malibu 1980, the fuel gauge reads way less than what is in the tank, if I hit the dashboard it comes back to life again ans shows the correct amount. How much trouble am I in, in terms of fixing this? Im hoping i don't have to dig in to deep, the plastics are fragile :O is...

Thank you, I'll just move the wire under the windshield wiper reservoir then :)

Okay i understand, you learn something everyday. My green wire looks just like the one you posted a pic of, I ended up just jamming a new wire into it and wrapping it over the sensor as you can see in my pic. Is the clip supposed to go sideways over the very end of the nipple? I would test it...

Ribbedroof, when you say that the gauge scale is not linear, does that mean that 220 is not operating temp? Because most cars that I am used to will be at operating temp when the gauge needle is dead in the middle. When I say operating temp i mean where temp usually settles, I don't know what...

Ribbedroof, ok so on the side of the nipple? I'll look into it. Glad I i didn't cut the connector on the wire as I did consider it. maybe it was just way to greasy for me to see anything :D

Alright, figured it out, if found the green wire, however the connector was square and would not fit on the sensor. The sensor has a round connector that would never fit on the wire connector, is the sensor missing a piece? However I tested the wire at a ground surface and got a full reading...

Okay, thank you. I have replaced my fender, that probably explains why my green wire is missing.... now I just have to find it

Alright, you are talking about the little round thing that sticks out between the 1 and 2. spark plugs? Where does the green wire exit the firewall? haven't seen a trace of it..

My temp gauge is stuck in the lowest possible reading all the time, i have the sport dash with the temp, volt, and oil gauge in a 1980 Malibu. I looked through some videos on youtube and everybody suggested that a ground wire on the engine-block was usually the cause when gauge is stuck at...

I have some issues with rust poking thru the white rust-protection tape/sticker on the lower sides of my car. Does anyone know if this is factory, and possibly a cheap replaceable trim-tape piece that you can order,? Or if this is this is not factory and has to be painted on with for-instance...

Okay, I'll begin with checking, and figuring where the slop is, and then I'll tighten up that nut. I'll get some help while I do it, there is always someone who knows more than I do, and think its fun when someone use the shop. And I'll get an opinion on what might be good/bad. I'll update you...

So I have to remove the entire driveshaft, at the transmission as well in order tighten up the pinion nut? I don't know exactly where the slop is, someone who helped me look at it told me it was a bearing inside of the transmission, but i can't confirm anything. I didn't even know about this...

Thank you, I will look at both of my manuals. But it sounds like a simple operation from what you explain. It shouldn't take to long either? When replacing the wheel bearing the other day, it got very close to the deadline after 5 hours, and not having the best of tools.

Thank you, i believe the universal joints was not the problems. so I will tighten up that nut according to the specs you gave me i guess. I will of course double check, but i can't really tell exactly what's wrong without a second opinion. But someone in the club that have 30 years of experience...

I am not entirely sure of what to do now. Where is the pinion nut even located?. When i have looked at the car with others that know more than me, They have showed me that there is slack in the driveshaft, as well as where the spider gears meet each other, and where the pinion shaft meets the...

There is movement in the diff, between the pinion and spider gears. While i'm driving i can hear the sound, its not very loud, and it goes away when putting my foot lightly on the accelerator pedal. It is also there in neutral. It sounds kind of like when a car is driving in reverse, only not...

I did of course use fresh oil, I refilled the diff with fresh oil a little over a week ago, and I drained it in a bucket and reused when opening the diff the third time. I did tilt the car high on its side to allow for proper oil before driving away after installing. (it was only a bit low on...