Toggle sidebar

seat belt receiver torx bolt hole location and torn seat belt replacement

P

paradigm

Apprentice
Aug 28, 2024
54
17
8
42
Does anyone know exactly where the torx bolt hole is for the T50 bolt that fastens the front seat belt receiver is? The car was re-carpeted, and I cannot feel through the carpet for the hole. I don't want to blindly cut the carpet either. I am thinking I may have to go under the car, around the trans / drive shaft and try and find the hole, but I really hope not to - I circled the general area behind the driver seat anchor where I believe it bolts in. Does anyone know how far away it is from the seat anchor?

Also which side (passenger or driver) does the receiver with the black wire harness bolt into? And what does this harness plug into? I am assuming some sort of signal to say whether the seat has been belted, so I guess the driver side?

Also the seat belt has torn as pictured below. Is it possible to not replace the ratcheting mechanism and only the cloth belt?

Which rearview mirror adhesive do you use?


seatbelts02.jpg


seatbelts01.jpg


seatbelts03.jpg
 
If you have a pawl (pokey device), then go under the car and jab it through the hole in the driveshaft tunnel. Even if you can't get it through the carpet you should be able to see where it is poking the carpet. Then put a small slice in the carpet in that spot. Two slices perpendicular to each other will give you enough room to get the belt belt bolt through.

I thought they were a T55, but I could be wrong. They suck to get in because the body nut is a lock nut.
 
  • Like
Reactions: Sweet_Johnny and Ugly1
Once upon a month or so ago I watched the girls do an interior replacement and your search and locate problem for the seat belts came up. In their case they were able to locate the hole from topside and what they did was to use the awl, or an ice pick, but they heated it up before punching it through the carpet. Why? Instead of tearing a rough hole and then having to go at it with an Olfa knife or box cutter, the heat caused the fibres around the hole to pull back and self seal, producing a smooth "finished" hole. I don't think it would matter if you elected to create the hole from below except that for the inner holes in the tunnel you might have to work around the drive shaft, meaning restricted maneuver room.

As for that damaged belt material. given that it is passing through the upper tab on the B Pillar, that pretty much puts the injury right in the middle of the belt. That in mind, while it might be possible to cut the belt and exise the damaged section, finding someone who would be willing to restitch the belt back together is quite another matter. That cute little label on the belt is there because the belt has to conform to established standards for safety. You try to have the belt repaired or reconstructed and there is no guarantee that the work will hold up and protect you in the event of a crash. On the other hand, if the belt is original and it fails as a consequence of a crash, you at least have grounds to go after the mfgr for cause, think law suit here. In addition, if you ever have to bring the car in for inspection and the inspector eyeballs your seatbelts, he/she/it can refuse/deny the certificate because the belt doesn't meet the stated standards for safety.




Nick
 
  • Like
Reactions: BuickOldsPontiac, Sweet_Johnny, RICKDIZZLE and 2 others
paradigm said:
Does anyone know exactly where the torx bolt hole is for the T50 bolt that fastens the front seat belt receiver is? The car was re-carpeted, and I cannot feel through the carpet for the hole. I don't want to blindly cut the carpet either. I am thinking I may have to go under the car, around the trans / drive shaft and try and find the hole, but I really hope not to - I circled the general area behind the driver seat anchor where I believe it bolts in. Does anyone know how far away it is from the seat anchor?

Also which side (passenger or driver) does the receiver with the black wire harness bolt into? And what does this harness plug into? I am assuming some sort of signal to say whether the seat has been belted, so I guess the driver side?

Also the seat belt has torn as pictured below. Is it possible to not replace the ratcheting mechanism and only the cloth belt?

Which rearview mirror adhesive do you use?


View attachment 249541

View attachment 249544

View attachment 249543
Click to expand...
this is an El Camino

1734302978767.png
 
  • Like
Reactions: Sweet_Johnny, RICKDIZZLE, 383_StealthRam and 1 other person
383_StealthRam said:
They're part way up the side of the trans/driveshaft tunnel. From the pic 86LK posted, here they are circled in red.
Click to expand...
Thanks guys for the photos thats what I felt with my hands today when I reached from underneath around the driveshaft or exhaust, and its tight in there. Ill try to get something to stick through there, maybe a piece of stiff wire and look for where it pokes on the inside of the car and cut the carpet there.
 
  • Like
Reactions: Sweet_Johnny
CopperNick said:
Once upon a month or so ago I watched the girls do an interior replacement and your search and locate problem for the seat belts came up. In their case they were able to locate the hole from topside and what they did was to use the awl, or an ice pick, but they heated it up before punching it through the carpet. Why? Instead of tearing a rough hole and then having to go at it with an Olfa knife or box cutter, the heat caused the fibres around the hole to pull back and self seal, producing a smooth "finished" hole. I don't think it would matter if you elected to create the hole from below except that for the inner holes in the tunnel you might have to work around the drive shaft, meaning restricted maneuver room.

As for that damaged belt material. given that it is passing through the upper tab on the B Pillar, that pretty much puts the injury right in the middle of the belt. That in mind, while it might be possible to cut the belt and exise the damaged section, finding someone who would be willing to restitch the belt back together is quite another matter. That cute little label on the belt is there because the belt has to conform to established standards for safety. You try to have the belt repaired or reconstructed and there is no guarantee that the work will hold up and protect you in the event of a crash. On the other hand, if the belt is original and it fails as a consequence of a crash, you at least have grounds to go after the mfgr for cause, think law suit here. In addition, if you ever have to bring the car in for inspection and the inspector eyeballs your seatbelts, he/she/it can refuse/deny the certificate because the belt doesn't meet the stated standards for safety.




Nick
Click to expand...
A few people have suggesting heating up an awl as you have on other sites, I may try that.

The belt will either need to be re-webbed professionally or replaced completely. Hopefully it isn't too difficult to remove the retractor part.
 
You must log in or register to reply here.

Similar threads

CrammerGram69
seat belt dye removal
Replies
6
Views
190
Interior
CrammerGram69
CrammerGram69
rogus
question on seat belts
Replies
5
Views
668
Interior
rogus
rogus
J
seat belt screw
Replies
2
Views
815
General Discussion
jlat
J
85 Cutty
04-06 GTO seats
Replies
11
Views
481
Interior
85 Cutty
85 Cutty

GBodyForum is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. Amazon, the Amazon logo, AmazonSupply, and the AmazonSupply logo are trademarks of Amazon.com, Inc. or its affiliates.

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor

Top Bottom