Search results

Yes,it does help thank you very much. I am running a 350 Chevy.

Is there one setup that is better or easier to use? From a Chevy truck or car. Found a couple one from 92 2500 truck and one from 87 Firebird.

I used Metro and it sucks. The roof rail seals are so thick the window will not go all the way up when the door is closed. :wtf: I know it has been awhile since this has been discussed, but I am just now finishing the car and all I have to do is put the door panels on. :wtf:

2 coats. If not humidity, maybe a bad can of paint?

I have used SEM interior paint on all my interior. Yesterday I painted the dash,scuffed it, applied the adhesion promoter, and paint. It looks cloudy,blotchy up close it looks fine buy move to a different angle and it looks bad. It was done outside about 80 degrees rainy. Could it be the...

I need to see if anyone has a pic of the p/s pump mounted up on a sbc 350 in a gbody. I must have the wrong bracket. I need to mount the pump,it has no a/c right now. The factory bracket must have gotten lost. I just need to know what I should be looking for. If you just want e-mail it to me you...

I know it is not a 78-88, but does anyone know where to get measurements or a template to put the rear decklid spoiler on a 72?

I was wondering which serpentine setup is best and commonly available.I have been told 88-92 v8 chevy trucks work well . Any info.

:?: Is there a factory type starter that will work on a 168 tooth flywheel and be smaller like a mini? Do I have to buy a aftermarket mini? When you have a 168 tooth flywheel is it always a stagger mount? I have a early 70s 350 chevy in my 78 Cutlass with a 350turbo.

I just wanted to tell you about the terrible experience I had with a business. The name is Larrys Performance also known as Track Pro. They advertise in some magazines. In short I called and ordered a set of heads from them and waited a little over a week, then called to seek info. and they told...

It is a 350 Chevy .040 over. It has a Performer intake and Performer 600cfm carb. I can see that the pistons are not flat top. I want a motor for my 78 Cutlass that has low speed torque. It will be primarily a street car.

Wouldnt a 64cc head be better than a 76cc. I know it depends on what you are looking to get out of the motor or the intended use of the vehicle.I bought a motor that I was able to hear run, I want to change the cam, I ran the head numbers and found out they are 1.72 1.50 valves and 76cc...

Like a moron, I did forget to put the steel washer on, I guess that is what happens when you try to hurry and do things. Thank you for all the help.

Thank You for the replies. Let me ask this, I installed 1inch lowering springs. Is it a must to install shocks made for lowering? I was wondering because now the top shock mounting nut is tight, but the shock itself is still loose. In other words I ran out of threads on the stud.Should I install...

I am installing 1 inch drop front springs on my Cutlass. The spring that came out has the ends that are both rounded. The new spring has one end that is flat, I am guessing that the flat end goes to the top?

I need door seals, trunk seal, and the seals where the door glass meets the body. Its for ac 78 cutlass 2dr. I also need rear bumper fillers ASAP.

Yea, I thought it was BS too. It makes no sense at all.

Looking in the Jegs catalog, I found the double hump crossmember for G-BODIES. They told me it fits Cutlass but not the Supreme. I called their tech. support and was told that, it would not fit because all Cutlass Supremes had the engine mounted off center, and the cross member would not work...

I have noticed that summit has shorty headers listed for g body cars. Has anyone ever tried them ? It would seem they would be easier to install.

Thanks for the info. it does help. :D