Search results

  1. Sodee

    LS turbo clocking and intercooler routings options

    I can confirm but Im pretty sure it is.
  2. Sodee

    LS turbo clocking and intercooler routings options

    My approach is similar to NorthernRegals, I just got tired of playing with it and went to town with a cutoff wheel. I'll clean it up later, or maybe not. Depends on how I feel lol 3" piping, 4" core, turbo will sit a little further from the engine than yours behind the inner passenger headlight
  3. Sodee

    LS turbo clocking and intercooler routings options

    second clocking option is going to be your best bet
  4. Sodee

    Early vs Late DBW Throttle body

    That’s what I’m figuring I’ll have to do. it reduces like that because of the 2.5” IC piping.
  5. Sodee

    Early vs Late DBW Throttle body

    I also have an unlicensed 03 p59 with IAC drivers, DBC TB if none of this is possible lol
  6. Sodee

    Early vs Late DBW Throttle body

    I pulled an unmolested harness from a DBW donor in the yard and realized that it’s a 03-07, instead of 99-02 like my engine, TB, PCM, pedal and Tac module. I also have the original harness from the engine for comparison but it’s a mess and not usable so I’m trying to find out my options. So...
  7. Sodee

    84Cutlass Supreme 5.3LS swap challenges.

    Are you keeping the swap stock? If so, have someone delete vats. Are you keeping the 60e? if so, just keep the stock converter and I would put some anti seize on the back of the block in case you need to pull it apart. Have you made decisions on the cross member? Driveshaft?
  8. Sodee

    84Cutlass Supreme 5.3LS swap challenges.

    This is an interesting thread.. building this car on a budget and within a specific timeline is going to be a challenge. ..like it’s been said, grind the welded mounts off, go to the parts store and get the SBC mounts. Put them in the correct holes and use the plates. It’ll fit. manifolds...
  9. Sodee

    What Did You Do To Your G-Body Today? [2021]

    Couldn’t get my broken studs out so now I gotta see if I can get someone to remove them 😕
  10. Sodee

    ‘85 Cutlass Grille Hardware

    Goodness, I owe you a beer for all this info.... thank you so much. I didn’t know they were 84 grilles, I just knew I preferred them over all others except the blacked out ones (they cost a lot). So much great info here, thank you a million times over.
  11. Sodee

    Mcss intercooler

    Nice to see GOOD pictures of cold side piping.. I was curious about how people were fitting FMICs
  12. Sodee

    What Did You Do To Your G-Body Today? [2021]

    This is kinda amazing.... wish I had power stuff now 😑
  13. Sodee

    What Did You Do To Your G-Body Today? [2021]

    Was going to say, I remembered pulling the long fitting out of the back hole of the trans. Thanks for clarifying !
  14. Sodee

    What Did You Do To Your G-Body Today? [2021]

    I can measure it tomorrow, I’m not 100% sure
  15. Sodee

    What Did You Do To Your G-Body Today? [2021]

    Installed 90 degree trans cooler fittings and 6an line fittings.. trans cooler and fan will be under the passenger side floor pan.. I think. The downpipe might be there so I may have to go with putting it under my feet. If I do that, I’ll angle the fittings towards the sky, and route the hose...
  16. Sodee

    ‘85 Cutlass Grille Hardware

    I am trying to properly mount these grills but i feel as though I am missing something. They don’t sit flush with the bumper, aren’t firmly mounted as they move. I also have an extra bracket? 2nd, what is the pitch of the bolts that secure the bracket to the header panel? I need 3-4 of these...
  17. Sodee

    What Did You Do To Your G-Body Today? [2021]

    I did a few things today.. Mocking up my drain line and figuring out the shifter stuff
  18. Sodee

    Lets Try this again: Cutlass Edition

    And using paper towels instead of a fitting wrench is poor status, but that’s pretty much the theme of this car lol along with the Brian Earl Spilner era an fittings but they too were cheap
  19. Sodee

    Lets Try this again: Cutlass Edition

    A little more work done today... and getting shifter routing down. It looks kinda like it should come with a longer cable but the shifter only cost $150 so I guess I got what I paid for lol

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor