BUILD THREAD Beautifying Beverly- We're Going Retro, Baby!

[Sweet_Johnny]

I felt it was time to start a build thread for my '81 C10 Silverado (Beverly) instead of continuing to clog up the "Non G Body" thread, so here we go. Many of you might be familiar with her already due to previous posts so the first one or two here will be rushed but still contain many pictures.

Short story: Had a truck picked out on Marketplace but the guy wasn't serious. After many other failed attempts I hopped on one last time while discussing said attempts with my father, and stumbled across something I could work with.



It was listed as being in my home town but was actually south of there, and the drive from my current residence was about the same so I immediately responded and went to check it out 2 hours later. I knew that it would have multiple issues at that price but figured a straight frame and a strong drivetrain made it worthwhile if the damage was within my purview, and I believe it to be so. There's just a lot of it to deal with. After seeing the mess, being warned of a transmission leak, and hearing it run a deal was struck for $2,200 cash. The following day I got a ride down to drive her home and get a feel for just how deep I stepped in "it", and the drive was quite informative: the speedo, temp, & fuel gauge didn't work; the brakes were abysmal; she shimmied down the road (quite violently at the time); the steering is shot; and the cab bounces on the frame. But she fires right up, doesn't smoke, and hits every gear.




Quite a few things under the hood were left disconnected after being tampered with, as the engine has supposedly been rebuilt and the transmission definitely got replaced at some time- actual mileage or specs on these is unknown. She's equipped with ESC but the knock sensor wire is cut/missing and the "tip in" vacuum switch is plugged, which jives with the replacement th350 transmission not needing it to control converter lockup. The ESC module is still wired (not bypassed) and provides spark but no ignition retard as it never thinks it needs to.




The body has a decent amount of rot and requires body mounts, new sealer everywhere, cab corners, outer rockers and possibly an inner, inner fender patchwork, doors, a hood, a complete interior, a rear bumper, and the bed needs attention by the wheel wells as well as underneath- the bracing is toast and the bolts are toothpicks. I have yet to check under the plastic liner. 🙄



Now, don't you worry your pretty lil head about how much the ol' gal needs: I held onto a boatload of parts (some new) from multiple squares that I've owned over the years and have a few twists in store as well.

 

[Sweet_Johnny]

After scrolling Marketplace for parts to accentuate what I had in storage I went to go get Beverly's tires re-mounted onto some Cragars I bought for $250. The Wranglers were old as hell and visibly cracked all over, as well as having various deformities due to how they were stored. They don't look so bad in the pics but one had a sizeable leak at the bead and I figured the No Names she came with were a better choice than the May Pops. Check out the blue bunny ears.




I purchased new bolt- in valve stems and a gang of new Dorman Mag lug nuts, threw a bunch of stuff in the truck, and went to the salvage yard since I trusted Ken to do the work more than the yahoos at the tire joints. After dropping off the Cragars for dismount I headed North to pick up some OER arm rests but ran into massive trouble when I simultaneously ran out of gas and plugged the filter that had been added near the carb. Much walking ensued, and the dog did not appreciate it but fresh gas was carried very quickly and we went back for our tires to be changed. The arm rests had to wait, and may or may not go into this truck anyway. This fun outing was subsequent to a similar one where I discovered that the fuel tank selector valve was stuck between tanks and not allowing much fuel flow and starving the carb.

Aside from different running shoes Beverly also received a glove box swap and a different door that actually contained glass. Shortly thereafter the hood and grille were removed as was the cowling, and I pulled the factory steering wheel in favor of the Walnut Grant that came in my El Camino. It's definitely not staying. The interior mirror is an Auto Zone special from years ago, and is a "chrome" piece that's framed with skulls.




I bought a seat for a Dodge because it fits the theme but would prefer a specific 60/40 split from an '88-94 Chevy/GMC, and they're NOT cheap when in good condition. According to Unique Auto Upholstery they also cost $800 minimum to re-cover since the material is glued to the foam. I found a guy parting out an '82 and snagged some 3" drop spindles complete with 1.25" rotors + accompanying calipers, stainless headers, a spare driveshaft, some wiring and hard lines, an intact factory fan shroud, and attempts to buy the 20 gallon driver's side gas tank have been fruitless. Another seller had a Power Plus aluminum intake and eBay provided complete upper and lower door panels. I started cleaning parts and prepping them for paint and proceeded to remove the "new but stored outside" lowering shackles + the leaf springs from my '86 C10 frame. They've had the overload springs removed but retain the factory Nylon/Teflon? sliders in between the leaves.

















I scraped the sealer from the cowl area, replaced it, and painted everything again after:




After blacking out the grille area with Rust Inhibitor Primer I installed the factory hood from my '85 Suburban as well as the grille it wore, though it's clearly not correct for the vehicle as it doesn't come close to fitting. I completely forgot that it was zip tied to the 'Burban and am working on a fix. I've already got it better than the following pic but not by much:

 

[Sweet_Johnny]

Those are aftermarket glass H4 housings that need a bit of adjustment as well as wiring + bulbs, and the bezels aren't correct for '81 but look better next to the grille. The horns don't work nor does the cigarette lighter and I believe they share a wire somewhere. I have no reverse lights, no dome light, and no cargo light either. The front left tire still leaks, possibly at the bead.

The passenger door got swapped but I don't have a picture of it, though I do have shot of when I scraped and replaced the sealer. Neither power window motor currently works but they did when I put them into storage- it could be a wiring compatibility issue but the plug does receive power from the switch. The truck is an '81 and the doors are '84 but the plugs were different as is one of their two wire colors, and I thought the major change to rotating ground was in '80 so I need to investigate further. I abhor the thought of having to swap the window motors but at least the power locks work without hesitation and the wing windows and slider window function as well. After doing the jamb I moved on to the floor then the kick panel before running out of product, and I used a cake decorating tool to try and keep the door seam looking decent but running tape lines would've been smart too. I'm just low on tape.




The cowl panel got sanded and hit with Sealer Primer, Filler Primer, spot sanded, and more Sealer before the previous pic, and then it received Black Sandable before I tried some Cranberry Gloss on the back. Nope. It looks Pink under a light, though it's supposed to be a fair bit darker. I'm now really, really leaning towards a Dark Cherry Metallic for a two-tone job but don't look forward to the potential issues of trying to do an entire truck with spray cans of metallic. I've had excellent results with spray cans but when I tried it with black metallic it had some zebra stripes + dark clouds, mostly from not maintaining an even distance and not keeping a good "wet edge" but possibly also from only having handheld halogen lights to do that particular job- I always wondered if their proximity to the work affected how the flake laid due to the heat. It was also my first time painting a car at all, and the following gloss jobs looked better and better as I learned along the way.



Same paint on a piece of receipt paper, in the house. I can't return it now because I'm an idiot:




In addition to cutting the exhaust off from the muffler back I also removed the rear bumper, which required an impact, a grinder, and a mini sledge.


Beverly's got a few mechanical issues that need sorted such as the entire braking system, but it's late so I'll save that for later. I haven't worked on that yet anyway.

 

[Sweet_Johnny]

Removed the plastic bed liner and it's not as bad as it could've been:



I vacuumed out a ton of sand, dirt, leaves, etc. but there's only a few spots that are rusted through and the panels/tubs are in great shape.