What did you buy for your G-body today? [2024]

Ugly1

Royal Smart Person
Oct 26, 2021
1,636
1,369
113
Lost in the woods of NH

ELCAM

Royal Smart Person
Jun 19, 2021
1,122
1,270
113
The potmetal (alumabronze) housing bolts into the tail gate and the lens and gasket screw onto the housing. You just remove the screws from the lens to change the bulb.

IMG_2024-01-25_16-23-30.jpg

IMG_2024-01-25_16-32-12.jpg
 
  • Like
  • Winner
Reactions: 2 users

Ugly1

Royal Smart Person
Oct 26, 2021
1,636
1,369
113
Lost in the woods of NH
Heading out tomorrow (Saturday) to look at a collection of parts to buy. Guy did a LS swap and is moving. So hopefully I get some goodie’s! No major body parts that might happen very soon.
 
  • Like
Reactions: 3 users

old80cs

G-Body Guru
Jun 27, 2013
626
2,057
93
Massachusetts
Nothing major, but found some NOS door pull covers. I only have one, not sure where they ended up after all these years in storage. Found three NOS pieces on eBay and got them today. Need to get a can spray paint to match the burgundy interior.

IMG_4802.jpeg
 
  • Like
Reactions: 3 users

Ugly1

Royal Smart Person
Oct 26, 2021
1,636
1,369
113
Lost in the woods of NH
Nothing major, but found some NOS door pull covers. I only have one, not sure where they ended up after all these years in storage. Found three NOS pieces on eBay and got them today. Need to get a can spray paint to match the burgundy interior.

View attachment 234222
Well dang wish I knew. Think I have two sets of those. In burgundy too, meaning 4 door panels. Could be wrong and have the insert style.
 
  • Like
Reactions: 1 users

old80cs

G-Body Guru
Jun 27, 2013
626
2,057
93
Massachusetts
Well dang wish I knew. Think I have two sets of those. In burgundy too, meaning 4 door panels. Could be wrong and have the insert style.
Guess I should start posting in the Parts Wanted section!

Like everything else, been looking off and on over the past several years. Have seen a few of these pop up but the prices were ridiculous. These three were reasonable so I grabbed them. Still looking for a used RH rear wheel opening molding, hoping one pops up soon.
 
  • Like
Reactions: 1 users

Ugly1

Royal Smart Person
Oct 26, 2021
1,636
1,369
113
Lost in the woods of NH
Guess I should start posting in the Parts Wanted section!

Like everything else, been looking off and on over the past several years. Have seen a few of these pop up but the prices were ridiculous. These three were reasonable so I grabbed them. Still looking for a used RH rear wheel opening molding, hoping one pops up soon.
Well… not sure how far you are from NH/ Massachusetts but found this on Craig’s list. Don’t think the 4 door is the same
IMG_5725.jpeg
 
  • Like
Reactions: 1 users

69hurstolds

Geezer
Supporting Member
Jan 2, 2006
8,196
17,598
113
Hmm. I guess we need to update for the new year before we get too deep into 2024.

Anyway, I botta'd a twin-groove PS pulley for less than the Dorman aftermarket. 6.13" diameter. Stamped code KN. P/N 22529402.

Fits 350R, 403, and 350N (diesel) with twin groove, and VIN 9 307 1984 (2nd design)- 1987, and some later 307 without A/C or B body Y 307. with dual groove.

2 groove pulley 22529402.jpg

2 groove pulley 22529402 b.jpg

2 groove pulley 22529402 a.jpg

2 groove pulley 22529402 c.jpg
 
  • Like
Reactions: 1 users

GBodyForum is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. Amazon, the Amazon logo, AmazonSupply, and the AmazonSupply logo are trademarks of Amazon.com, Inc. or its affiliates.

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor