Search results

Hey all. Havent been on here ina while... Her she is... 78 MC Landau has 75k original miles.Dont mind the rims, theyre coming off real soon.. Ive been putting her together for the past few months... My baby has 383 stroker wit dart heads: alotta goodies...she has 4:10 in the rear 3500 b&m...

on my chevy 350 trans im sure i adjusted the linkages correctly. when the car is started it goes into park fine but every gear i shift into on the shifter makes it drive forward.no reverse no neutral, just drive. when the car is off but the ignition is on and i shift into reverse the car rolls...

Right now Im having bad sttering problems. its not a G body but its an 89 Caprice. When I had my 22's on there the car wandered a little but not a lot.Now I have 14s on there and I was scared for my life. I tried my best but, I had to cancel a booty call I had setup 2nite. I jacked the front...

Well, I swapped in my new 700r4 and its all good. Now i have another problem. My car barely heats up and my radiator is hissing. When I squeeze my top rad hose i hear air pushing through the top corner on the driver's side. The owner told me I would need a water pump soon. How do I know what it...

WIll I have a hard time using a 4L60E trans with my fuel injected 305? As far as wiring?

Where is the temp sending unit on a fuel injected 305?

I picked up a non G Body car today and It has what I believe to be a trans problem. First of all the engine is a 305 and from the pan, the trans looks like its a 2004R. When I put the car in gear, it feels like theres a stall in the trans. The car doesnt move until I get the RPM's a little...

Would a fuel injected Vortec motor be able to be swapped into a GBody? I mean as far as engine wiring and such. A buddy of mine has a Vortec motor in his 06 Trailblazer SS and he's taking out the whole drivetrain. How would I get one to work?

Well to make a long story short, look at the pics..its for sale now for $1500 with the rims. detroit,mi its kinda dark now to show the crank but the key broke right off and when it broke, it took a chunk outta the crank. im not going thru the process of fixing it. its outta here. im fixing my bu...

What gear ratio is in a 1983 monte ss. I have one and a guy told me it has a limited slip with 3:73's. I want more opinions. Im thinking of swapping the whole rear into my Cutlass.

Does anybody have a diagram of an 82 Cutlass Fuse Panel showing the location/order of fuses and their ratings? Some of my labels are faded and some I dont know what correct fuse each takes. Ive read in the Chiltons Manual and it isnt in there. THIS WOULD BE A BIG HELP AND GREATLY...

I have a manual choke carb. Anyone know how to set up the choke/ fast idle on an Edelbrock carb. I want it so when I start the car up for the first time it will idle at about 1500rpm and when I tap the pedal, I want it to kick down to 1000rpm. As of now Im stuck with pumping the gas/ cranking...

First Im running a Edelbrock 600 carb on my mild sbc 350. It idles fine at 1k, when I put it in gear, its still dropping to 4-550 rpm. Ive tried my timing everywhere from 10 to 20 intial. Its currently at 17intial and about 32-34 all in 2500. A guy I know actually had it running good, both in...

Well I went to start my car this morning and the battery was dead. I thought it was the new radio I just installed. The radio blew a fuse, I swapped the fuse with a new and then took the radio out altogether. Spent all day on slow charger. Got it started took it for a 10-15 min drive. Cut the...

To make a long story short I broke a stud and Im pissed. How do you replace it? I already went to the auto parts store and got a replacement stud.

Hey guys. Im picking up a set of 15in Cragar SST's to throw on the Cutty. The front are 15x6 and the rears are 15x10. I dont know too much about small rims and tires. I want some pretty fat and wide tires on the rear and ok size on the front. ANd I may get some BFG's, idk yet. What size tire...

Im finally starting my bodywork today. It takes forever to take off the paint with a orbital sander. I shouldve spent the money on a DA. Anyway I started off sanding the trunk and Im working my way forward. Everything that wasnt masked and painted is getting replaced..(TAIL lIGHTS) I still...

How do you use an adjustable vacuum advance canister to benefit? When to adjust and not?

Im having problems with my power accesories from my cam. I have a Comp Cams 279THF7 cam. It has a .479/.465 lift and adv duration is 279/297 and @.050 duration is 227/241.. It runs nice and strong at idle in park. As soon as I put it in gear its real choppy and the rpms drop a couple hundred...

What kind of exhaust system r these guys running? Anybody know?...........Sounds killer.......man......... http://www.youtube.com/watch?v=I20MI4Lgubs&playnext_from=TL&videos=K5Yz1x5e27A&feature=grec