Search results for query: crank

The number I was getting was same 594-142, and it's wrong. Found crank.... So at least you know 3.2 to 3.8 to 4.2 are all the same as far as crank shows. So balancer should all be same from 3.2 to 4.2 V6.

...is reading 12.4 at battery and when read at starter. the problem is when i go to start, the starter clicks repeatedly and never actually cranks. while connected to float charger the battery some times reads at high as 14.5, gets momentary attempt at cranking then continues to click. starter...

...I measure 3.5" difference. I got the Transdapt bellhousing adapter installed and used the orange locktite on the block to adapter and on the Speedmaster neutral balance flexplate to crank bolts, torqued to 60 ft-lbs. I also trimmed the extra aluminum on both sides to clear the headers on install.

cars over heating when idling. when driving it goes down. im going to wrap the manifolds and down pipes. When im idling it overheats if i open the hood the temp goes down. im going to get turbo covers when i figure this dam cam issue. again it won read rpm, but if i upload the cam free tune from...

I am facking retahded, I have the Comp crank socket that accommodates the degree wheel. I forgot that I had it LOL

This is my first ride. Tecumseh 3.5hp side shaft on a truck bike frame. VW crank pulley bolted to the rear drive wheel. FAST! I raced my friend Charly who had a 5hp RUPP and we ran neck and neck down 93rd avenue for 10 blocks. 1968 or so? 'Them were the days my friend, we thought they'd never...

That would be for the 231 being even or odd fire if I'm remembering right.

Lol. It’s the only pic I have. It’s a 3.900 stroke crank.

...module. Anyway parts store didn't have an oil pressure switch in stock so I just put the old one back in. I go to fire up the car and crank it four or five times of not starting and then remember that I forgot to plug the distributor back in. Get the two connectors plugged back in and hop...

Personally I have used 20w50 being thicker and was what I was going to use. But either way before cranking the engine I had pumped it through the system with a drill and a custom crank bar of a screwdriver and metal sleeve to ensure-A) no oil plugs forgotten ( did it once 4 qts of oil on the...

440-ish @ the crank.

Well, that depends on if the MSD can run the 58X with a 1X Cam Sensor. Why are you going to 58X? There are plenty of 24X 4" Cranks out there I've built a few stroker LS Engines with them.

...throttle. I was thinking it was something like piston slap? Sorry if this is something obvious, just trying to get some help and knowledge from folks that know a lot more than me. I took a video of a cold start with the distributer wire disconnected and just cranked it. What do you guys think?

The other end of it bud.. 🤣 I take it that's built as a Stroker Engine using the LS7 Crank to get the 4" Stroke..never seen an 8 bolt Crank as 3.900..

...the epoxy primer I brushed on. The Kevko pan is a nice piece, 3 trap doors and a relatively tight baffle system with a windage tray and a crank scraper, which cleared perfectly: Feels a hair thicker than the stock pan I had, so much so that I couldn’t use the spreader rails with the...

Sorry assumed it was a chebby 350. Agree with above gonna need to remove the distributor cap and crank the engine and see if the distributor turns.

I don't want to sound too forward, but nice nuts. Making that coupler was probably cheaper as well as faster than buying one from a store.

...air available. This happens when you pump too much gas into the intake before starting (like pumping it when the engine is warm) then it just cranks with the throttle plates closed. However, in this case, either a sinking float, or the return line plugged causes the primary fuel bowl to...

...$100 to $350 305 $50 (or free) to $250 350 $150 to $350 350 4 bolt, maybe about $75 to $125 extra if block is in good shape and no damage to crank mains. Around 2015 top dollar for a 350 Vortec was about $1000 all day long, any where you go. Now 2024... $500-ish 305 long or short block...

...Even the base gaskets were different, so another Carb purchase later, I have the one supposedly that should work on a 68 Olds 350. It still cranks and cranks with no firing. For the first time, the cranking is not lopey or labored, it really sounds like it is trying to fire even, like...