Kore3 C5 Front and Rear question

[CDUNIGAN1981]

Im here for the installation pictures

I'll post when I get there. Reaching out to SSM tomorrow to finalize front suspension. Afterwards, I'm making decisions about kore3 kits. Not sure how I feel about no parking brake in rear. Get the feeling 355mm up front might be too much for my 18"s as I've read certain American Racing wheels have issues even in 18", needless to say, I'm measuring.

With that, if I'm all eyes myself.

 

[carnutjw]

http://www.kore3.com/tech.php#fitment_templates. Scroll down to templates. You might have to scale your printout to make it right, there's a ruler on the side. Transfer to cardstock/poster board and check fit on the inside of your wheel. Also, if you order from them you get a pdf with multiple pages of instructions and 3D illustrations, very easy to understand and install.

 

[CDUNIGAN1981]

http://www.kore3.com/tech.php#fitment_templates. Scroll down to templates. You might have to scale your printout to make it right, there's a ruler on the side. Transfer to cardstock/poster board and check fit on the inside of your wheel. Also, if you order from them you get a pdf with multiple pages of instructions and 3D illustrations, very easy to understand and install.

I did see this but didn't immediately understand how to use it until just now. When I read 'wheel hub ' I just assumed I needed my hubs installed on my spindles first so I walked away from it after about 3 seconds of reading.

First time caller...yikes

Thanks for pointing this out. It will allow me to order it sooner.

 

[CDUNIGAN1981]

I emailed kore3 for an opinion.
With that, does this look right?

I mean at the risk of affirming my ignorance.
Did I do this right?
Is 3/8" okay?

Corey

 

[Dayzedandkonfuzed]

I mean at the risk of affirming my ignorance.
Did I do this right?
Is 3/8" okay?

Corey

Oh yea bud. I dont think I even have 1/4" on my front setup, almost had to grind the fins down.

Corvette C5 Brakes on Stock G-Body Spindle

Stumbled across this, so I had to give it a shot: Modify your stock hubs and spindles to upgrade to Corvette C5 brakes (12.8" rotors) I managed to get spindles and rotors from a Malibu at pick n pull, so I was able to keep my daily driver on the road for most of this build. First you have to...

gbodyforum.com

 

[CDUNIGAN1981]

Oh yea bud. I dont think I even have 1/4" on my front setup, almost had to grind the fins down.

Corvette C5 Brakes on Stock G-Body Spindle

Stumbled across this, so I had to give it a shot: Modify your stock hubs and spindles to upgrade to Corvette C5 brakes (12.8" rotors) I managed to get spindles and rotors from a Malibu at pick n pull, so I was able to keep my daily driver on the road for most of this build. First you have to...

gbodyforum.com

What size wheel were you working with?

 

[Dayzedandkonfuzed]

17's

 

[CDUNIGAN1981]

Oh yea bud. I dont think I even have 1/4"

Tight fit but the template seemed exact!
I put this picture on my build thread but thought this may help forum searches.

 

[CDUNIGAN1981]

More pics

 

[CDUNIGAN1981]

http://www.kore3.com/tech.php#fitment_templates. Scroll down to templates. You might have to scale your printout to make it right, there's a ruler on the side. Transfer to cardstock/poster board and check fit on the inside of your wheel. Also, if you order from them you get a pdf with multiple pages of instructions and 3D illustrations, very easy to understand and install.

Super helpful pointing this out my guy!