MONTE CARLO Park to drive not shifting correctly

Status
Not open for further replies.

Freddyflores559

Not-quite-so-new-guy
Jan 23, 2023
5
1
3
1988 Monte Carlo ss

Ok so idk if this been asked before but here’s my problem.

From park to drive ,or reverse to drive it stalls to kick in to gear . It will take anywhere from 30 seconds to Minute to kick into gear. Since I’ve had the car I’ve would step on the brake and give it gas till kicks into gear that would be the fastest way to kick into drive . Well from doing that a couple times I busted the u joints to the drive line. So I stopped doing that . So I started putting it in the lowest gear and give it a lol rev and kick into gear .
Mind you once it’s in drive and it shifts fine.
But the problem is from park to drive,reverse to drive or even neutral to drive .

I came across a video on YouTube the link is below and let me know if that video would help my problem.

 

CopperNick

Comic Book Super Hero
Supporting Member
Feb 20, 2018
3,347
3,011
113
Canada
Before you go ahead with any invasive surgery here, have you checked the tension on your TV cable? When you lift the air cleaner off the air horn of the carburetor or TBI, you should see a bracket that supports two cables. The upper one is the accelerator cable and the lower is the TV cable. All this has been covered in earlier threads and on You-B00b but to summarize, the Th200R4 does not use vacuum to tell it when to shift, it relies on internal pressure, which is why the video suggests to swap out that switch. When you attempt to accelerate, the movement of the throttle cable also causes the TV cable to react. If the cable is too tight or slack, the shift won't come at the correct time. Too tight and it shifts too early and very hard; too slack and the shifts are late or not at all.

if you do find that cable is mis-tensioned, then it can be adjusted, and I did post a how to for this last year at some point so the local search engine ought to be able to retrieve it for you, or it can be found in one of the service manuals that Haynes or Chilton publish. If there is no obvious slack or extreme tension then the cable can still be at fault if it is damaged inside its outer cover or has gotten rusty. The cable can be swapped out for a new one without removing the t-mission but the cute little metric bolt that holds the cable boss to the t- case is a grade two item and very soft and prone to be eroded due to age and road exposure.

The reason that I suggest this as a to do first is that, as the video implies, accessing the internals of the t-mission is an invasive exercise that the commentator is doing while the car is on a lift; in short, under ideal conditions. While this could be done in a driveway or in a one car garage, if anything goes wrong or you break something else, or the oil that comes out of the pan is black and smelly and there is a lot of debris in the pan bottom, then you have to figure out how to get the car to a shop that deals with auto-stick boxes and have them take over the job. That could cost you as most shops like to do the whole thing from step one and not get called in halfway through because something went wrong.

Not trying to discourage you here; good to see you want to take a run at it and wrench your own ride. Just be aware that videos can skip things under the assumption that the viewer already has some experience or has access to reference material for assistance and that they do tend to get made, mostly, under fairly ideal conditions. You don't often see a video of someone in a pick a part yard slithering under a hulk to grab parts because dealing with rust and corroded parts and nasty working conditions aren't things a lot of people want to see. In addition, when you do come across them, they are not live action, meaning that the video was likely edited for both time and the removal of minor details like prolonged or intense bouts of cursing and swearing when something, a bolt or nut, refuses to move or breaks, or a part or tool gets lost, or when the inevitable damage to a finger or hand occurs. (Not planning on mentioning the possible need to deal with resident varmints of various kinds and levels of danger here)

Pictures and progress posts are always enjoyed if you get the time to post them.


Good luck,


Nick
 
  • Like
Reactions: 1 user

Freddyflores559

Not-quite-so-new-guy
Jan 23, 2023
5
1
3
Before you go ahead with any invasive surgery here, have you checked the tension on your TV cable? When you lift the air cleaner off the air horn of the carburetor or TBI, you should see a bracket that supports two cables. The upper one is the accelerator cable and the lower is the TV cable. All this has been covered in earlier threads and on You-B00b but to summarize, the Th200R4 does not use vacuum to tell it when to shift, it relies on internal pressure, which is why the video suggests to swap out that switch. When you attempt to accelerate, the movement of the throttle cable also causes the TV cable to react. If the cable is too tight or slack, the shift won't come at the correct time. Too tight and it shifts too early and very hard; too slack and the shifts are late or not at all.

if you do find that cable is mis-tensioned, then it can be adjusted, and I did post a how to for this last year at some point so the local search engine ought to be able to retrieve it for you, or it can be found in one of the service manuals that Haynes or Chilton publish. If there is no obvious slack or extreme tension then the cable can still be at fault if it is damaged inside its outer cover or has gotten rusty. The cable can be swapped out for a new one without removing the t-mission but the cute little metric bolt that holds the cable boss to the t- case is a grade two item and very soft and prone to be eroded due to age and road exposure.

The reason that I suggest this as a to do first is that, as the video implies, accessing the internals of the t-mission is an invasive exercise that the commentator is doing while the car is on a lift; in short, under ideal conditions. While this could be done in a driveway or in a one car garage, if anything goes wrong or you break something else, or the oil that comes out of the pan is black and smelly and there is a lot of debris in the pan bottom, then you have to figure out how to get the car to a shop that deals with auto-stick boxes and have them take over the job. That could cost you as most shops like to do the whole thing from step one and not get called in halfway through because something went wrong.

Not trying to discourage you here; good to see you want to take a run at it and wrench your own ride. Just be aware that videos can skip things under the assumption that the viewer already has some experience or has access to reference material for assistance and that they do tend to get made, mostly, under fairly ideal conditions. You don't often see a video of someone in a pick a part yard slithering under a hulk to grab parts because dealing with rust and corroded parts and nasty working conditions aren't things a lot of people want to see. In addition, when you do come across them, they are not live action, meaning that the video was likely edited for both time and the removal of minor details like prolonged or intense bouts of cursing and swearing when something, a bolt or nut, refuses to move or breaks, or a part or tool gets lost, or when the inevitable damage to a finger or hand occurs. (Not planning on mentioning the possible need to deal with resident varmints of various kinds and levels of danger here)

Pictures and progress posts are always enjoyed if you get the time to post them.


Good luck,


Nick
Thanks I will try that first . At the moment I do t have my car at my house . I have to make room in my garage to bring the car home . Thanks for all the info and I will definitely follow your steps first before I go under the car . And I will post pics on the process. Thanks again !!
 

Freddyflores559

Not-quite-so-new-guy
Jan 23, 2023
5
1
3

Attachments

  • E077F757-0702-4190-A27C-85A6D137F60D.jpeg
    E077F757-0702-4190-A27C-85A6D137F60D.jpeg
    4.4 MB · Views: 66
  • AE7AA698-4D58-4315-A5A9-F1DD70FDF7F2.jpeg
    AE7AA698-4D58-4315-A5A9-F1DD70FDF7F2.jpeg
    757.9 KB · Views: 66
  • 60B9EB6A-33B3-462E-8CB6-17896EFE9EDD.jpeg
    60B9EB6A-33B3-462E-8CB6-17896EFE9EDD.jpeg
    170.3 KB · Views: 72

Freddyflores559

Not-quite-so-new-guy
Jan 23, 2023
5
1
3
Idk who Tyan is but hope my pics says different lol
9303926B-DC04-420F-A21D-9582F9073CB2.jpeg
8D67FA09-C47B-491B-BB26-8D2377E935EF.jpeg
E6ABBA21-07B3-411D-90B9-13293DB59B47.jpeg
BCD5C86C-E298-494A-B679-75521A84C96C.jpeg
49A7EE75-852B-4747-8C76-0AF2E971D7FC.jpeg
DECB6816-9D20-41B8-AE2A-458972427CDE.jpeg
23C7346F-3520-4F3C-9D93-C52D2FAC7792.jpeg
7DF3467D-2F09-4B29-8CB8-BFA7397ECEB3.jpeg
ED4934B7-5E7E-4E13-AD9C-7D79333EC358.jpeg
D7A29416-E357-43B3-9206-D1D7DC4208C6.jpeg
A8F9BAB1-E8D6-43A6-AC36-F759FBB0BF9F.jpeg
67F9C9BA-6E7C-481D-AC6D-27A213C76A6E.jpeg
E6653092-DFBD-4313-9DB4-FA7F4089F078.jpeg
9A0459B9-3658-4F60-92F9-7B502E79BAC8.jpeg
458B7640-1102-430C-8F86-26FC1BB86201.jpeg
050B8BF7-C33C-44C6-B850-AD80561AD8E1.jpeg
F36E6FDD-C9AE-455E-9EBF-38297D7BBEDB.jpeg
9303926B-DC04-420F-A21D-9582F9073CB2.jpeg
8D67FA09-C47B-491B-BB26-8D2377E935EF.jpeg
9303926B-DC04-420F-A21D-9582F9073CB2.jpeg
8D67FA09-C47B-491B-BB26-8D2377E935EF.jpeg 9303926B-DC04-420F-A21D-9582F9073CB2.jpeg 😝
 

Attachments

  • 0AFD0165-D90A-4751-A3A6-E402296F84EE.jpeg
    0AFD0165-D90A-4751-A3A6-E402296F84EE.jpeg
    208.8 KB · Views: 59
  • 1A4CC278-3811-4B91-AFA1-D10270BFBD03.jpeg
    1A4CC278-3811-4B91-AFA1-D10270BFBD03.jpeg
    196.9 KB · Views: 63
  • 3A6552CE-076B-4817-B4CE-52F5DAA43DDD.jpeg
    3A6552CE-076B-4817-B4CE-52F5DAA43DDD.jpeg
    998.6 KB · Views: 62
  • E5596993-D8B2-4611-B30C-65E294DA987A.jpeg
    E5596993-D8B2-4611-B30C-65E294DA987A.jpeg
    145.2 KB · Views: 63
  • CBB546E7-3702-45D7-8B62-B3C4D8365431.jpeg
    CBB546E7-3702-45D7-8B62-B3C4D8365431.jpeg
    85.6 KB · Views: 64
  • 0C748436-3AC3-4DBD-BB4B-5361D7BA466A.jpeg
    0C748436-3AC3-4DBD-BB4B-5361D7BA466A.jpeg
    271.2 KB · Views: 61
  • D46BE52E-0F6C-4F79-B839-EF3ACE97406A.jpeg
    D46BE52E-0F6C-4F79-B839-EF3ACE97406A.jpeg
    229.9 KB · Views: 66
  • Like
Reactions: 1 user

olskool

Apprentice
Sep 26, 2021
82
122
33
if it is hesitating like you say there is a couple of things it can be. the simple things first, low in fluid, clogged filter. the internal problems, if it does this cold, then gets better as it heats up, the rubber seals inside are hard. when they heat, they expand, and pressure builds, and it goes in gear. if it does it all the time cold or hot, the pump can be worn out, the pressure regulator valve can be stuck or the PR spring can be broken, they are located in the pump. all this will cause low line pressure, if that is the case then when you floor it from a stand still it should chatter or slip, but that is not an absolute. the reverse boost valve can also be stuck causing this.,,,,,,,,,,,,,,,,,
 
Status
Not open for further replies.

GBodyForum is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. Amazon, the Amazon logo, AmazonSupply, and the AmazonSupply logo are trademarks of Amazon.com, Inc. or its affiliates.

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor