BUILD THREAD “The Juggernaut”

Took these last night after returning home from a 2 day work road trip in which I drove over 1000kms (and worked) in less than 48 hours.

Popped the tinted marker lights in quickly now that the lower half of the bodywork is done and it’s standing vertical again, and maybe it’s just the exhaustion delirium talking, but the tinted lights are quickly growing on me.

They don’t look quite as purple as I thought they did earlier, and I’m loving the overall look.

IMG_4783.jpeg


IMG_4784.jpeg


Can’t wait to get back on it again this weekend.
 
Looks great! Donovan has more time in his bumper than all the body work in my last two project cars and it shows!
 
Been gone for awhile and it's good to see your progress. Killer work D. !!!

Thank you Tony, it’s nice to see you back! Thanks for catching up on the progress.

Starting to accumulate some stuff on the to-do list now that packages are arriving and other things are starting to gel.

I received my Summit order yesterday, a pair of 2” taller upper mounts for my RideTech Shockwave front airbag/shock combinations:

IMG_4785.jpeg


IMG_4786.jpeg


The Shockwaves I currently have are the older versions, so hopefully these upper extensions will still fit and work properly. They have the shock valving adjustment knob located on the top vs on the side of the bottom on mine.

IMG_4789.jpeg


IMG_4790.jpeg


Why am I going to replace these you ask? Because with the way the car is currently set up, the ride height setting on the computer controlled AccuAir system is still a little too low to provide adequate wheel and tire clearance, even with the recently added Malibu fender flares. I only have about a quarter of an inch clearance from the fenders with the wheels turned at ride height. One small bump at that configuration is going to lead to fender damage.

Now yes, I could compensate for this by increasing the air pressure to the front Shockwaves to lift the front end up, but that isn’t really the correct way to address the issue. It would ultimately decrease the available suspension travel, and increase the front suspension travel resistance leading to a harsher ride. By increasing the length of the shock, this way I can regain the additional height needed and not have to sacrifice the other parameters.

Now, do I think I need 2” of additional travel? No I do not. I much rather would’ve preferred something in the 1”-1 1/2” range, but 2” was the shortest available from RideTech. Hopefully it doesn’t affect the static height too much when it is aired down as I love the way it looks when it’s slammed.

In addition to the upper mounts, I also purchased the clamping tool that will be required to hold the shock shaft for removal/installation without damaging it:

IMG_4787.jpeg


IMG_4798.jpeg


On the bumper project, the now shortened bumper shock substitutions have been sent right back out again, this time for powder coating. I feel confident enough that my measurements are accurate that I won’t have to have them modified again. Just waiting for the call to come pick them up, it should hopefully be sometime next week.

I’m still waiting on USPS to get my package from Mr. 69hurstolds, at they speed they move, maybe by Christmas.
🙄

And the one other thing I need to update on, is the modified height 3D printed mirror gaskets. At very long last, I FINALLY have a viable product that I will be able to work with. I won’t go into too much in-depth detail here, but this has been an EXTREMELY long drawn out process.

Months were spent on creating, testing and modifying the computer file for them, followed by months more of 3D printing test pieces and refining those. I’ve had the assistance of the guys at work more versed in the intricacies of the 3D printing world on this, and, after several failed attempts using regular filament, we ultimately decided to print them in resin. The resin versions will be much easier to modify and add to/refine if necessary, and the finish is much nicer than with filament. The other major upside to resin is that it’s UV stable as that’s how it’s cured, whereas the filament is not. It would eventually break down and disintegrate over time when exposed to the elements.

There were a couple of issues with getting these printed out too, mostly related to the file, but last week I was finally presented with a tangible finished product:

IMG_4791.jpeg


IMG_4792.jpeg


IMG_4793.jpeg


IMG_4794.jpeg


They are still in their rawest unfinished state at the moment, but it’s something I can finally work with.

IMG_4795.jpeg


The backsides will have to be ground and sanded flat and flush, these bumps are from something in the file that didn’t translate well into the end product.

IMG_4796.jpeg


Not too concerned though as that’ll be easy to remove.

IMG_4797.jpeg


So once I finish the bumper project and can switch gears into addressing these other little projects, I’ll be crossing these off the list one by one. Once I’m certain that these gaskets are perfect, they’ll have to be prepped and painted satin black so that they appear factory.

Because that’s just the way I roll.
😎

D.
 
Thank you Tony, it’s nice to see you back! Thanks for catching up on the progress.

Starting to accumulate some stuff on the to-do list now that packages are arriving and other things are starting to gel.

I received my Summit order yesterday, a pair of 2” taller upper mounts for my RideTech Shockwave front airbag/shock combinations:

View attachment 242816

View attachment 242817

The Shockwaves I currently have are the older versions, so hopefully these upper extensions will still fit and work properly. They have the shock valving adjustment knob located on the top vs on the side of the bottom on mine.

View attachment 242819

View attachment 242820

Why am I going to replace these you ask? Because with the way the car is currently set up, the ride height setting on the computer controlled AccuAir system is still a little too low to provide adequate wheel and tire clearance, even with the recently added Malibu fender flares. I only have about a quarter of an inch clearance from the fenders with the wheels turned at ride height. One small bump at that configuration is going to lead to fender damage.

Now yes, I could compensate for this by increasing the air pressure to the front Shockwaves to lift the front end up, but that isn’t really the correct way to address the issue. It would ultimately decrease the available suspension travel, and increase the front suspension travel resistance leading to a harsher ride. By increasing the length of the shock, this way I can regain the additional height needed and not have to sacrifice the other parameters.

Now, do I think I need 2” of additional travel? No I do not. I much rather would’ve preferred something in the 1”-1 1/2” range, but 2” was the shortest available from RideTech. Hopefully it doesn’t affect the static height too much when it is aired down as I love the way it looks when it’s slammed.

In addition to the upper mounts, I also purchased the clamping tool that will be required to hold the shock shaft for removal/installation without damaging it:

View attachment 242818

View attachment 242821

On the bumper project, the now shortened bumper shock substitutions have been sent right back out again, this time for powder coating. I feel confident enough that my measurements are accurate that I won’t have to have them modified again. Just waiting for the call to come pick them up, it should hopefully be sometime next week.

I’m still waiting on USPS to get my package from Mr. 69hurstolds, at they speed they move, maybe by Christmas.
🙄

And the one other thing I need to update on, is the modified height 3D printed mirror gaskets. At very long last, I FINALLY have a viable product that I will be able to work with. I won’t go into too much in-depth detail here, but this has been an EXTREMELY long drawn out process.

Months were spent on creating, testing and modifying the computer file for them, followed by months more of 3D printing test pieces and refining those. I’ve had the assistance of the guys at work more versed in the intricacies of the 3D printing world on this, and, after several failed attempts using regular filament, we ultimately decided to print them in resin. The resin versions will be much easier to modify and add to/refine if necessary, and the finish is much nicer than with filament. The other major upside to resin is that it’s UV stable as that’s how it’s cured, whereas the filament is not. It would eventually break down and disintegrate over time when exposed to the elements.

There were a couple of issues with getting these printed out too, mostly related to the file, but last week I was finally presented with a tangible finished product:

View attachment 242822

View attachment 242823

View attachment 242824

View attachment 242825

They are still in their rawest unfinished state at the moment, but it’s something I can finally work with.

View attachment 242826

The backsides will have to be ground and sanded flat and flush, these bumps are from something in the file that didn’t translate well into the end product.

View attachment 242827

Not too concerned though as that’ll be easy to remove.

View attachment 242828

So once I finish the bumper project and can switch gears into addressing these other little projects, I’ll be crossing these off the list one by one. Once I’m certain that these gaskets are perfect, they’ll have to be prepped and painted satin black so that they appear factory.

Because that’s just the way I roll.
😎

D.
Very interested in seeing how the extention works. And I think we can all say that this is possibly the most work done on mirror gaskets. Ever.
 
Well, for the first time ever, tonight I tested positive for Covid.

I managed to avoid it all through the Pandemic for years now, but yesterday it caught up with me. I’m not too concerned about it, just another cold to get over, but it’s going to put a serious crimp in the bumper progress in the next little while.

In the meantime here’s a couple quick pictures of the most recent progress, it’s coming along well.

IMG_4799.jpeg


IMG_4800.jpeg


IMG_4801.jpeg


IMG_4802.jpeg


IMG_4804.jpeg


And as if that wasn’t enough of a kick in the a$$, the other night I learned that I’m losing my storage spot for Olds Cool in my neighbors garage. He needs me to move it out so that he can access his ‘50 Chevy sedan to ready it for sale. That’s really going to interfere with my plans for the Juggernaut moving forward.

So once I kick this crap, I now have to clean and reorganize The Skunkworks to make room for Olds Cool again. It’s going to be do-able, but just a major PITA.

D.
 
Well, for the first time ever, tonight I tested positive for Covid.

I managed to avoid it all through the Pandemic for years now, but yesterday it caught up with me. I’m not too concerned about it, just another cold to get over, but it’s going to put a serious crimp in the bumper progress in the next little while.

In the meantime here’s a couple quick pictures of the most recent progress, it’s coming along well.

View attachment 243081

View attachment 243082

View attachment 243083

View attachment 243084

View attachment 243086

And as if that wasn’t enough of a kick in the a$$, the other night I learned that I’m losing my storage spot for Olds Cool in my neighbors garage. He needs me to move it out so that he can access his ‘50 Chevy sedan to ready it for sale. That’s really going to interfere with my plans for the Juggernaut moving forward.

So once I kick this crap, I now have to clean and reorganize The Skunkworks to make room for Olds Cool again. It’s going to be do-able, but just a major PITA.

D.
I hope you feel better soon!
 

GBodyForum is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. Amazon, the Amazon logo, AmazonSupply, and the AmazonSupply logo are trademarks of Amazon.com, Inc. or its affiliates.

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor