What did you do to your shop today?

[ck80]

That is lucky. Leave it to me to forget once and run the door over the roof of a car. Then again, if it didn't clear, you could just do a door lift.

You know, there's an easy answer.

You put whichever of the wife's cars you hate/hate working on the most on top of the lift.

Then, smack it with the door.

Use insurance proceeds to pay for renovation raising the roof and/or removing that garage door "so it wouldn't happen to her other car".

 

[fleming442]

Getting there

That's a problem

 

[Turbo Zach]

Getting there View attachment 173411
That's a problem
View attachment 173412

Looks like there is a lot of stuff that doesn't belong in a shop in there? Do you have any other garages?

 

[ck80]

Looks like there is a lot of stuff that doesn't belong in a shop in there? Do you have any other garages?

Comes with being a family man... the days of the single use shop/garage and it remaining the man cave are... well, facing extinction.

I actually have permission from the wife to build a temporary shop (something between 40x40 and 36x64) prior to the next house to solve just that problem.

It's funny, I just sold that same shop vac, and got more than it cost me.

 

[Turbo Zach]

Comes with being a family man... the days of the single use shop/garage and it remaining the man cave are... well, facing extinction.

I actually have permission from the wife to build a temporary shop (something between 40x40 and 36x64) prior to the next house to solve just that problem.

It's funny, I just sold that same shop vac, and got more than it cost me.

The funny thing is the older I get the more I see the importance of having a shop of my own. I have young kids and I am getting old fast. I am also blessed with having outbuildings to store stuff. I have a 30×40 shop and hope to add another 25 feet to it in the near future. The tractor and skid loader need to get out of my car shop!

 

[motorheadmike]

Put the clear cup away for now, put on the #7 ceramic and set for 15cfm gas flow. Set it for 95amps, add like 10 pulse per second and 60% or so duty cycle on the pulse. When you get puddle started throttle back on the peddle a bit so it will follow the torch and move more quickly with the torch head angled about 15-20 degrees toward direction of travel. Also get comfortable for a short stitch, like 1.5" and allow cooling for like 1 minute before you restart.

This was high frequency and 85A on 20 gauge, but all the other settings you mentioned above. 95A gave me blow through.



Watched a bunch of "beginners" and "common mistakes" videos today too. I am glad I did a bunch of stuff wrong yesterday so I know what less wrong looks like today. My plan is to practice about an hour a day or so.

I think we need a welding thread.

 

[Burd]

I picked up a 1978 dealership poster, a parts guy gave me one, think maybe I’ll frame it for the garage. 16x20:

 

[motorheadmike]

I only have a single 220v outlet in my garage. So what do you do when you're a one man show with a welder, air compressor and hoist that need it at any one time?

Plugging and unplugging things gets old fast.

Here's my next endeavour:

This three-way switch and a few other outlets, should make things a bit nicer. Especially with the extension cords dropping power closer to where I need it.

 

[mclellan83]

I only have a single 220v outlet in my garage. So what do you do when you're a one man show with a welder, air compressor and hoist that need it at any one time?

Plugging and unplugging things gets old fast.

Here's my next endeavour:

View attachment 173526View attachment 173527

This three-way switch and a few other outlets, should make things a bit nicer. Especially with the extension cords dropping power closer to where I need it.

 

[Burd]

I recently cleaned up my moms 1948 kitchen table for the garage. I’ll put coffee and bloody Mary’s on it at my annual cars and coffee.