442

Hi all, I am new to this and hope i can get some help with my cutlass build here in Seattle. I have a 1986 white t-top Cutlass 442. Currently I dropped a GM 350 Goodwrench (1006636) it also has some heads with casting number 4036, so not sure what I have. I am new to carburetor motors so I keep...

I’v tore down almost everything needed so far. What other bolts are there for Power Steering pump. Two on left side of bracket and one on bracket from Alternator? Do I have to pull the pulley off the PS? 85 442

Congrats to "new guy" and winner of November's GBotM, Hurst so good.

Alright guys, finally at the stage where I'm contemplating on how to rebuild the rearend in the Cutlass. I have one of the desired 8.5" from a 442 that currently has stock axles, a Richmond powertrax posi and the stock 3:73's. The posi makes some odd noises at low speeds due to a bent axle issue...

Im think of trading for a 88 cutlass which is 77k original miles. It is an original LV2 car which from what little I could find are pretty rare. It now however as really nice fresh paint but is done up like a 442. Any idea what the value of it is?

Hey all, I am brand new to the forum but have used the information on here many times throughout the course of my G-body build. I have a 1986 Olds 442. Bit of a back story, my grandfather bought it and drove it for awhile before my father purchased it from him. When I graduated high school it...

Car and Driver, July 1985.

Car and Driver, July 1985.

Car and Driver, July 1985.

Car and Driver, July 1985.

Car and Driver, July 1985.

Car and Driver, July 1985.

Car and Driver, July 1985.

Hello, this is my first post so hopefully it goes smooth. I recently bought an 83' Hurst Olds, everything seemed great up until now. I was doing some research on the vin and it doesn't have the 9 in the vin code, but when i run the vin it comes up as an 83' my first thought was i have a clone...

Located in MA, the nanny-state. Runs great, just over 100k miles. Original 307 and quadrajet; Hurst shifters work great. PM me for more info, will send pictures as well as more contact info, as well as answer any questions. Asking $5k. Firm price.

So I'm looking to pick a few brains here, I'm messing around with the semi-rat 87 442, the car is just a hobby car I've having fun with.. Little back ground when I purchased the car the CEL was on and found no fuse for the ECM in the fuse block. Put in a fuse, CEL went out. Any ways I'm...

So Ive been messing with the 87 442 off and on through the winter, I had a feeling when I bought it that the car has a few electrical gremlins... Upon purchase the check Engine light was on... I didn't have my dx tools with me, but figured it was nothing major and took a gamble... Found out the...

I have a 1986 Chevrolet Monte Carlo SS and I just bought an Avital alarm system that I intend to install myself. I need to know what wires to splice or tap for the starter, horn, lights, door switches, electric locks, and electric trunk release. I've installed audio equipment numerous times in...

sup fellas? I just picked up this 87 442 with 135k on the dash for a great price. one owner car, small rust bubbles on the bottom of the doors. no trim on the body, which leads me to believe its been painted. but I've seem both trim and no trim 87 442's. slow poke stock 307 needing a tune up and...

In my other Thread about the Q-jet I said I was going to put the Performance chip in. And I did that. ( Pictured Above ). I matched the Icons on both ends of it to, I guess , place it in properly. Got in and fired her up. Idled really high for a bit then kicked down to about 2500rpm. then down...