What did you do to your G-Body today? [2011-2018]

Status
Not open for further replies.
Got my washer bottle off an cleaned it up a bit,used a green scotch brite pad an Orange hand cleaner,on the outside,the inside i used bleach an some pennys Polished the cap too
 

Attachments

  • pizap.com10.90858025196939711392590994031.jpg
    pizap.com10.90858025196939711392590994031.jpg
    94.3 KB · Views: 618
  • pizap.com10.0070130201056599621392590938765.jpg
    pizap.com10.0070130201056599621392590938765.jpg
    87.8 KB · Views: 610
  • pizap.com10.66085222084075211392590883359.jpg
    pizap.com10.66085222084075211392590883359.jpg
    109.8 KB · Views: 608
  • pizap.com10.24892465304583311392590756703.jpg
    pizap.com10.24892465304583311392590756703.jpg
    106.5 KB · Views: 609
  • pizap.com10.91652166284620761392590828000.jpg
    pizap.com10.91652166284620761392590828000.jpg
    101 KB · Views: 601
Too cold and too much snow in PA,to want to get in my,shop and do anything, lol.
 
Got the 78 Cutlass Supreme that was given to me running today after it had sat for 13 years. Just running off gas that i poured in the float bowl of the Q-Jet. Surprised it started an ran because three plug wires where broke in two.
 
Started to work on my passenger wheel well today, got some holes filled in that i don't need,there is also a big hole under the support brace ,were the tire rubbed threw, Not going to worry about it though "wouldn't see it" from the engine bay
 

Attachments

  • pizap.com10.323790768627077341392668971140.jpg
    pizap.com10.323790768627077341392668971140.jpg
    99.4 KB · Views: 536
Got some more work done to the drivers wheel well. Also got my new light bezels an got the lights cleaned up an buffed by hand. Also shoveled a sh*t load of snow today 6" got about a foot an half all together out there, more coming
 

Attachments

  • pizap.com10.86896296823397281392752205015.jpg
    pizap.com10.86896296823397281392752205015.jpg
    112.4 KB · Views: 511
  • pizap.com10.45200826413929461392751936765.jpg
    pizap.com10.45200826413929461392751936765.jpg
    123.7 KB · Views: 509
  • pizap.com10.73410216299816971392752999078.jpg
    pizap.com10.73410216299816971392752999078.jpg
    123.3 KB · Views: 519
Cleaned up some wiring and installed a Painless digital power manager and negative battery kill switch. This way, when I work on the car, I do not have to disconnect both batteries, just twist off the connector and get to work.
udydune2.jpg
be9ejaby.jpg
esegeged.jpg



Sent from my iPad using Tapatalk
 
Chased the car cover down the street. 50 mph gusting winds tonight in northern New Mexico. Tied the b*st*rd back on front to back as well as side to side. Payback for a nice weekend...that weather is in another zip code by now.
 
Went to the junk yard an bought this MINT trunk lid No rust or dents for 40.00 bucks,Happier than a pig in sh*t ,Got it put on,but it's really close to the quarter panel edges "both sides" hardly any gap, Any suggestions ?
 

Attachments

  • pizap.com10.53180754557251931392943166375.jpg
    pizap.com10.53180754557251931392943166375.jpg
    70.5 KB · Views: 419
  • pizap.com10.85880408901721241392943044171.jpg
    pizap.com10.85880408901721241392943044171.jpg
    70.1 KB · Views: 434
Status
Not open for further replies.

GBodyForum is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. Amazon, the Amazon logo, AmazonSupply, and the AmazonSupply logo are trademarks of Amazon.com, Inc. or its affiliates.

Please support GBodyForum Sponsors

Classic Truck Consoles Dixie Restoration Depot UMI Performance

Contact [email protected] for info on becoming a sponsor